ISO 10350-1:2017
Current
Current
The latest, up-to-date edition.
Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Language(s)
French, English
Published date
10-11-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.
The ISO 10350 series identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions. The properties included are those presented conventionally in manufacturers' data sheets. ISO 10350-1 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials that may be injection- or compression-moulded or prepared as sheets of specified thickness. For the purposes of ISO 10350-1, long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding.
NOTE ISO 10350-2 deals specifically with long- or continuous-fibre-reinforced plastics.
| DevelopmentNote |
Supersedes ISO/DIS 10350-1. (10/2017)
|
| DocumentType |
Standard
|
| Pages |
12
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| UNE-EN ISO 10350-1:2018 | Identical |
| DIN EN ISO 10350-1:2018-03 | Identical |
| UNE-EN ISO 10350-1:2008 | Identical |
| I.S. EN ISO 10350-1:2008 | Identical |
| BS EN ISO 10350-1 : 2008 | Identical |
| EN ISO 10350-1:2017 | Identical |
| UNI EN ISO 10350-1 : 2014 | Identical |
| DIN EN ISO 10350-1:2016-08 (Draft) | Identical |
| DIN EN ISO 10350-1:2001-03 | Identical |
| NS EN ISO 10350-1 : 2017 | Identical |
| SN EN ISO 10350-1 : 2018 | Identical |
| ONORM EN ISO 10350-1 : 2018 | Identical |
| BS EN ISO 10350-1:2017 | Identical |
| NEN EN ISO 10350-1 : 2017 | Identical |
| I.S. EN ISO 10350-1:2017 | Identical |
| NBN EN ISO 10350-1 : 2008 AMD 1 2014 | Identical |
| PN EN ISO 10350-1 : 2017 | Identical |
| NF EN ISO 10350-1 : 2017 | Identical |
| NEN ISO 10350-1 : 2007 | Identical |
| BS EN ISO 16396-2:2017 | Plastics. Polyamide (PA) moulding and extrusion materials Preparation of test specimens and determination of properties |
| ISO 178:2010 | Plastics Determination of flexural properties |
| PREN ISO 7792-2 : DRAFT 2011 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 7792-2:2012 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 7792-2:2012) |
| 14/30304058 DC : 0 | BS EN ISO 17855-2 - PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 17422:2002 | Plastics. Environmental aspects. General guidelines for their inclusion in standards |
| UNE-EN ISO 19069-2:2016 | Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19069-2:2016) |
| 15/30315534 DC : 0 | BS EN ISO 16396-2 - PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 20753 : 2008 | PLASTICS - TEST SPECIMENS |
| UNE-EN ISO 17855-2:2016 | Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 17855-2:2016) |
| DIN EN ISO 16396-2:2017-07 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017) |
| BS EN ISO 178 : 2010 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES |
| I.S. EN ISO 7391-2:2006 | PLASTICS - POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 899-1:2017 | Plastics - Determination of creep behaviour - Part 1: Tensile creep (ISO 899-1:2017) |
| DIN EN ISO 20753 E : 2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| UNI EN 15860 : 2010 | PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| ISO 28078-2:2009 | Plastics Poly(phenylene sulfide) (PPS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| I.S. EN ISO 899-1:2017 | PLASTICS - DETERMINATION OF CREEP BEHAVIOUR - PART 1: TENSILE CREEP (ISO 899-1:2017) |
| ASTM D 5592 : 1994 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| DIN EN ISO 20753:2014-07 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| DIN EN ISO 15103-2:2007-09 | PLASTICS - POLY(PHENYLENE ETHER) (PPE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 75-2:2013-08 | PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 2: PLASTICS AND EBONITE (ISO 75-2:2013) |
| ISO 75-3:2004 | Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics |
| ISO 15103-2:2007 | Plastics Poly(phenylene ether) (PPE) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 19069-2:2016 | Plastics — Polypropylene (PP) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 11403-3:2014 | Plastics. Acquisition and presentation of comparable multipoint data Environmental influences on properties |
| BS EN ISO 7391-2:2006 | Plastics. Polycarbonate (PC) moulding and extrusion materials Preparation of test specimens and determination of properties |
| DIN EN ISO 1872-2:2000-12 | PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 11403-2:2012 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES (ISO 11403-2:2012) |
| DIN EN ISO 8257-2:2006-06 | PLASTICS - POLY(METHYL METHACRYLATE) (PMMA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 178:2013-09 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010 + AMD.1:2013) |
| DIN EN ISO 3672-2:2002-07 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 16/30310691 DC : 0 | BS EN ISO 294-1 - PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS |
| I.S. EN ISO 178:2010 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010) |
| 17/30349217 DC : 0 | BS EN ISO 21970-2 - PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 27547-1:2010 | Plastics. Preparation of test specimens of thermoplastic materials using mouldless technologies General principles, and laser sintering of test specimens |
| UNE-EN ISO 9988-2:2015 | Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 9988-2:2006) |
| 05/30132990 DC : DRAFT APR 2005 | ISO 20753 - PLASTICS - TEST SPECIMENS |
| 05/30091855 DC : DRAFT MAR 2005 | ISO 1874-2 - PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| ISO 18263-2:2015 | Plastics Mixtures of polypropylene (PP) and polyethylene (PE) recyclate derived from PP and PE used for flexible and rigid consumer packaging Part 2: Preparation of test specimens and determination of properties |
| PREN ISO 11403-1 : DRAFT 2012 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO/DIS 11403-1:2012) |
| 12/30237823 DC : 0 | BS EN ISO 75-2 - PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 2: PLASTICS AND EBONITE |
| DIN EN ISO 19069-2:2016-07 | PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 19069-2:2016) |
| ISO 20753:2008 | Plastics Test specimens |
| BS ISO 8257-2:1990 | Plastics. Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Preparation of test specimens and determination of properties |
| EN ISO 11403-1:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014) |
| EN ISO 11403-3:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014) |
| ONORM EN ISO 14910-2 : 2013 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013) |
| ISO 20558-2:2018 | Plastics — Poly(phenylene sulfide) (PPS) moulding and extrusion materials — Part 2: Preparation of test specimen and determination of properties |
| PREN 15860 : DRAFT 2016 | PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| ISO 20029-2:2017 | Plastics Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Part 2: Preparation of test specimens and determination of properties |
| ONORM EN ISO 7391-2 : 2006 | PLASTICS - POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| UNE-EN ISO 25137-2:2017 | Plastics - Sulfone polymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 25137-2:2009) |
| UNE-EN ISO 20028-2:2017 | Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 20028-2:2017) |
| BS EN ISO 20753:2014 | Plastics. Test specimens |
| DIN EN ISO 1874-2:2013-03 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1874-2:2012) |
| DIN EN ISO 75-3:2004-09 | Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics (ISO 75-3:2004) |
| DIN EN ISO 295:2004-05 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004) |
| DIN EN ISO 14530-2:2000-08 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14530-2:1999); German version EN ISO 14530-2:1999 |
| UNE-EN ISO 11403-1:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014) |
| BS EN ISO 1874-2:2012 | Plastics. Polyamide (PA) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 14528-2:2000 | Plastics. Melamine-formaldehyde powder moulding compounds (MF-PMCs) Preparation of test specimens and determination of properties |
| BS EN ISO 1872-2:2007 | Plastics. Polyethylene (PE) moulding and extrusion materials Preparation of test specimens and determination of properties |
| DIN EN ISO 7391-2:2006-06 | PLASTICS - POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 11403-1:2014 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO 11403-1:2014) |
| I.S. EN ISO 75-3:2004 | PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 3: HIGH-STRENGTH THERMOSETTING LAMINATES AND LONG-FIBRE-REINFORCED PLASTICS |
| I.S. EN ISO 8257-2:2006 | PLASTICS - POLY(METHYL METHACRYLATE) (PMMA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 294-1:2017 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS (ISO 294-1:2017) |
| I.S. EN ISO 15103-2:2007 | PLASTICS - POLY(PHENYLENE ETHER) (PPE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 2898-2:2008 | PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 8256:2004 | PLASTICS - DETERMINATION OF TENSILE-IMPACT STRENGTH |
| DIN EN ISO 1873-2:2000-12 | PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 75-2:2013 | PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 2: PLASTICS AND EBONITE (ISO 75-2:2013) |
| I.S. EN ISO 11403-3:2014 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014) |
| I.S. EN ISO 3673-2:2012 | PLASTICS - EPOXY RESINS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES OF CROSSLINKED EPOXY RESINS (ISO 3673-2:2012) |
| I.S. EN ISO 1874-2:2012 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1874-2:2012) |
| BS EN ISO 25137-2:2017 | Plastics. Sulfone polymer moulding and extrusion materials Preparation of test specimens and determination of properties |
| 15/30327856 DC : 0 | BS ISO 20558-2 - PLASTICS - POLY(PHENYLENE SULFIDE) (PPS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMEN AND DETERMINATION OF PROPERTIES |
| 14/30304062 DC : 0 | BS EN ISO 19069-2 - PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 11/30236286 DC : 0 | BS EN ISO 11963 - PLASTICS - POLYCARBONATE SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS |
| 17/30333280 DC : 0 | BS ISO 17422 - PLASTICS - ENVIRONMENTAL ASPECTS - GENERAL GUIDELINES FOR THEIR INCLUSION IN STANDARDS |
| 08/30160325 DC : DRAFT MAR 2008 | BS ISO 27547-1 - PLASTICS - PREPARATION OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS USING MOULDLESS TECHNOLOGIES - PART 1: GENERAL PRINCIPLES, AND LASER-SINTERING OF SPECIMENS |
| 14/30283167 DC : 0 | BS ISO 18263-2 - PLASTICS - MIXTURES OF POLYPROPYLENE (PP) AND POLYETHYLENE (PE) RECYCLATE DERIVED FROM PP AND PE USED FOR FLEXIBLE AND RIGID CONSUMENR PACKAGING - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN ISO 17855-2:2016 | Plastics. Polyethylene (PE) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN 62631-3-2:2016 | Dielectric and resistive properties of solid insulating materials Determination of resistive properties (DC Methods). Surface resistance and surface resistivity |
| 13/30240167 DC : 0 | BS ISO 16365-2 - PLASTICS - THERMOPLASTIC POLYURETHANES FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 25137-2 : 2009 | PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 18263-2:2015 | Plastics. Mixtures of polypropylene (PP) and polyethylene (PE) recyclate derived from PP and PE used for flexible and rigid consumer packaging Preparation of test specimens and determination of properties |
| 15/30328314 DC : 0 | BS EN ISO 20557-2 - PLASTICS - POLY(PHENYLENE ETHER) (PPE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMEN AND DETERMINATION OF PROPERTIES |
| 01/121538 DC : DRAFT APRIL 2001 | BS EN ISO 899-1 PLASTICS - DETERMINATION OF CREEP BEHAVIOUR - PART 1: TENSILE CREEP |
| BS ISO 3672-2 : 2000 AMD 13326 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 16/30317348 DC : 0 | BS EN 15860 - PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| 08/30165044 DC : DRAFT FEB 2008 | BS ISO 28078-2 - PLASTICS - POLY(PHENYLENE SULFIDE) (PPS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 02/120706 DC : DRAFT FEB 2002 | BS EN ISO 8256 - PLASTICS - DETERMINATION OF TENSILE-IMPACT STRENGTH |
| BS ISO 28078-2:2009 | Plastics. Poly(phenylene sulfide) (PPS) moulding and extrusion materials Preparation of test specimens and determination of properties |
| ONORM EN ISO 20753 : 2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| I.S. EN ISO 17855-2:2016 | PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 17855-2:2016) |
| UNI EN ISO 178 : 2013 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES |
| I.S. EN ISO 25137-2:2017 | PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 25137-2:2009) |
| EN ISO 7391-2:2006 | Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7391-2:2006) |
| EN ISO 20029-2:2018 | Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimen and determination of properties (ISO 20029-2:2017) |
| ISO 17282:2004 | Plastics — Guide to the acquisition and presentation of design data |
| I.S. EN ISO 8986-2:2009 | PLASTICS - POLYBUTENE-1 (PB-1) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| UNI EN ISO 11403-1 : 2014 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES |
| UNE-EN 15860:2011 | Plastics - Thermoplastic semi-finished products for machining - Requirements and test methods |
| DIN EN ISO 8256:2005-05 | Plastics - Determination of tensile-impact strength (ISO 8256:2004); German version EN ISO 8256:2004 |
| DIN EN ISO 11403-3:2014-09 | Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014) |
| DIN EN ISO 11403-1:2014-09 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014) |
| UNE-EN ISO 294-1:2017 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:2017) |
| BS EN ISO 3673-2:2012 | Plastics. Epoxy resins Preparation of test specimens and determination of properties of crosslinked epoxy resins |
| BS EN ISO 8256:2004 | Plastics. Determination of tensile-impact strength |
| ISO 17855-2:2016 | Plastics — Polyethylene (PE) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| UNE-EN ISO 11403-2:2012 | Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012) |
| BS EN ISO 11403-2:2012 | Plastics. Acquisition and presentation of comparable multipoint data Thermal and processing properties |
| ISO 2898-2:2008 | Plastics Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| DIN EN ISO 3673-2:2012-10 | Plastics - Epoxy resins - Part 2: Preparation of test specimens and determination of properties of crosslinked epoxy resins (ISO 3673-2:2012) |
| I.S. EN ISO 294-3:2003 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - SMALL PLATES |
| UNE-EN ISO 1874-2:2013 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:2012) |
| EN ISO 294-3:2003 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:2002) |
| EN ISO 9988-2:2015 | Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 9988-2:2006) |
| EN ISO 25137-2:2017 | Plastics - Sulfone polymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 25137-2:2009) |
| UNI EN ISO 1874-2 : 2013 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| UNI EN ISO 3673-2 : 2012 | PLASTICS - EPOXY RESINS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES OF CROSSLINKED EPOXY RESINS |
| UNI EN ISO 11403-2 : 2012 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES |
| UNI EN ISO 7792-2 : 2013 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| UNI EN ISO 2898-2 : 2009 | PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| UNI EN ISO 75-2 : 2013 | PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 2: PLASTICS AND EBONITE |
| UNI EN ISO 14910-2 : 2013 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| UNI EN ISO 8986-2 : 2010 | PLASTICS - POLYBUTENE-1 (PB-1) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN ISO 20029-2:2018 | Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Preparation of test specimens and determination of properties |
| 12/30255180 DC : 0 | BS EN ISO 11403-1 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES |
| BS ISO 16365-2:2014 | Plastics. Thermoplastic polyurethanes for moulding and extrusion Preparation of test specimens and determination of properties |
| I.S. EN ISO 1873-2:2007 | PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 1872-2:2007 | PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 11/30242905 DC : 0 | BS EN ISO 3673-2 - PLASTICS - EPOXY RESINS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 11/30192003 DC : 0 | BS EN ISO 7792-2 - PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN ISO 20028-2:2017 | Plastics. Thermoplastic polyester (TP) moulding and extrusion materials Preparation of test specimens and determination of properties |
| I.S. EN ISO 9988-2:2015 | PLASTICS - POLYOXYMETHYLENE (POM) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 9988-2:2006) |
| BS ISO 9988-2 : 2006 | PLASTICS - POLYOXYMETHYLENE (POM) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 05/30128281 DC : DRAFT JAN 2005 | ISO 9988-2 - PLASTICS - POLYOXYMETHYLENE (POM) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 9988-2:2015-05 | PLASTICS - POLYOXYMETHYLENE (POM) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 9988-2:2006) |
| DIN EN 15860:2016-07 (Draft) | PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| I.S. EN ISO 14910-2:2013 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013, CORRECTED VERSION 2015-12-15) |
| 17/30354769 DC : 0 | BS EN ISO 29988-2 - PLASTICS - POLYOXYMETHYLENE (POM) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 03/118818 DC : DRAFT DEC 2003 | BS EN ISO 7391-2 - PLASTICS - POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN ISO 19069-2:2016 | Plastics. Polypropylene (PP) moulding and extrusion materials Preparation of test specimens and determination of properties |
| 17/30335677 DC : 0 | BS EN ISO 178 - PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES |
| 15/30304408 DC : 0 | BS EN ISO 20029-2 - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| UNI EN ISO 20753 : 2014 | PLASTICS - TEST SPECIMENS |
| UNE-EN ISO 16396-2:2017 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017) |
| I.S. EN ISO 20029-2:2018 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMEN AND DETERMINATION OF PROPERTIES (ISO 20029-2:2017) |
| I.S. EN ISO 20753:2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| I.S. EN 15860:2010 | PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| I.S. EN 62631-3-2:2016 | DIELECTRIC AND RESISTIVE PROPERTIES OF SOLID INSULATING MATERIALS - PART 3-2: DETERMINATION OF RESISTIVE PROPERTIES (DC METHODS) - SURFACE RESISTANCE AND SURFACE RESISTIVITY |
| ISO 14910-2:2013 | Plastics Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Part 2: Preparation of test specimens and determination of properties |
| DIN EN ISO 20028-2:2015-08 (Draft) | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017) |
| PREN ISO 75-2 : DRAFT 2011 | PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 2: PLASTICS AND EBONITE (ISO/DIS 75-2:2011) |
| ASTM D 5592 : 1994 : R2010 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| EN ISO 20753:2014 | Plastics - Test specimens (ISO 20753:2008) |
| ISO 16365-2:2014 | Plastics — Thermoplastic polyurethanes for moulding and extrusion — Part 2: Preparation of test specimens and determination of properties |
| ISO 17422:2002 | Plastics Environmental aspects General guidelines for their inclusion in standards |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| UNI EN ISO 11403-3 : 2014 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES |
| DIN EN ISO 294-1:2017-09 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS (ISO 294-1:2017) |
| UNE-EN ISO 14910-2:2014 | Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:2013, Corrected version 2015-12-15) |
| UNE-EN ISO 7792-2:2013 | Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7792-2:2012) |
| BS EN ISO 14529-2:2000 | Plastics. Melamine/phenolic powder moulding compounds (MP-PMCs) Preparation of test specimens and determination of properties |
| ISO 1873-2:2007 | Plastics Polypropylene (PP) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 1873-2:2007 | Plastics. Polypropylene (PP) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 10724-2:2001 | Plastics. Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) Small plates |
| ISO 14528-2:1999 | Plastics Melamine-formaldehyde powder moulding compounds (MF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 20028-2:2017 | Plastics — Thermoplastic polyester (TP) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 3672-2:2001 | Plastics. Unsaturated-polyester resins (UP-R) Preparation of test specimens and determination of properties |
| BS EN ISO 75-2:2013 | Plastics. Determination of temperature of deflection under load Plastics and ebonite |
| ISO 1874-2:2012 | Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 294-3:2003 | Plastics. Injection moulding of test specimens of thermoplastic materials Small plates |
| BS EN ISO 295:2004 | Plastics. Compression moulding of test specimens of thermosetting materials |
| ISO 14530-2:1999 | Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 8257-2:2001 | Plastics Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 14529-2:1999 | Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 3672-2:2000 | Plastics — Unsaturated-polyester resins (UP-R) — Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 75-3:2004 | Plastics. Determination of temperature of deflection under load High-strength thermosetting laminates and long-fibre-reinforced plastics |
| BS EN ISO 14527-2:2000 | Preparation of test specimens and determination of properties |
| ISO 7792-2:2012 | Plastics Thermoplastic polyester (TP) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 16396-2:2017 | Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 8257-2:2006 | Plastics. Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Preparation of test specimens and determination of properties |
| ISO 25137-2:2009 | Plastics Sulfone polymer moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 14526-2:1999 | Plastics Phenolic powder moulding compounds (PF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 294-1:2017 | Plastics. Injection moulding of test specimens of thermoplastic materials General principles, and moulding of multipurpose and bar test specimens |
| ISO 8986-2:2009 | Plastics Polybutene-1 (PB-1) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 9988-2:2006 | Plastics Polyoxymethylene (POM) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 3673-2:2012 | Plastics — Epoxy resins — Part 2: Preparation of test specimens and determination of properties of crosslinked epoxy resins |
| UNE-EN ISO 11403-3:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014) |
| UNE-EN ISO 75-2:2013 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013) |
| BS EN ISO 11403-1:2014 | Plastics. Acquisition and presentation of comparable multipoint data Mechanical properties |
| BS EN ISO 14526-2:2000 | Plastics. Phenolic powder moulding compounds (PF-PMCs) Preparation of test specimens and determination of properties |
| EN ISO 8257-2:2006 | Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 8257-2:2001) |
| EN ISO 11403-2:2012 | Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012) |
| EN ISO 2898-2:2008 | Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2898-2:2008) |
| EN ISO 15252-2:1999 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 15252-2:1999) |
| EN ISO 8986-2:2009 | Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 8986-2:2009) |
| EN ISO 19069-2:2016 | Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19069-2:2016) |
| EN ISO 294-1:2017 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:2017) |
| EN ISO 1873-2:2007 | Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1873-2:2007) |
| EN ISO 14529-2:1999 | Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14529-2:1999) |
| EN ISO 1874-2:2012 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:2012) |
| EN ISO 10724-1:2001 | Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 1: General principles and moulding of multipurpose test specimens (ISO 10724-1:1998) |
| EN ISO 10724-2:2000 | Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 2: Small plates (ISO 10724-2:1998) |
| EN ISO 3672-2:2001 | Plastics - Unsaturated-polyester resins (UP-R) - Part 2: Preparation of test specimens and determination of properties (ISO 3672-2:2000) |
| EN ISO 16396-2:2017 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017) |
| EN ISO 14530-2:1999 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14530-2:1999) |
| EN ISO 14528-2:1999 | Plastics - Melamine-formaldehyde powder moulding compounds (MF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14528-2:1999) |
| EN ISO 8256:2004 | Plastics - Determination of tensile-impact strength (ISO 8256:2004) |
| EN ISO 20028-2:2017 | Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 20028-2:2017) |
| EN ISO 17855-2:2016 | Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 17855-2:2016) |
| EN ISO 1872-2:2007 | Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1872-2:2007) |
| EN ISO 14526-2:1999 | Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14526-2:1999) |
| EN ISO 3673-2:2012 | Plastics - Epoxy resins - Part 2: Preparation of test specimens and determination of properties of crosslinked epoxy resins (ISO 3673-2:2012) |
| EN ISO 14910-2:2013 | Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:2013, Corrected version 2015-12-15) |
| EN ISO 15103-2:2007 | Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15103-2:2007) |
| EN ISO 75-2:2013 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013) |
| EN ISO 295:2004 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004) |
| EN ISO 7792-2:2012 | Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7792-2:2012) |
| EN ISO 14527-2:1999 | Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF-MF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14527-2:1999) |
| DIN EN ISO 17855-2:2016-06 | PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 17855-2:2016) |
| I.S. EN ISO 19069-2:2016 | PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 19069-2:2016) |
| 07/30152076 DC : 0 | BS ISO 25137-2 - PLASTICS - SULFONE PLASTICS (SP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN 15860:2010 | Plastics. Thermoplastic semi-finished products for machining. Requirements and test methods |
| 08/30170332 DC : DRAFT JAN 2008 | BS EN ISO 8986-2 - PLASTICS - POLYBUTENE-1 (PB-1) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 15/30304402 DC : 0 | BS EN ISO 20028-2 - PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN ISO 9988-2:2015 | Plastics. Polyoxymethylene (POM) moulding and extrusion materials Preparation of test specimens and determination of properties |
| PREN ISO 11963 : DRAFT 2011 | PLASTICS - POLYCARBONATE SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS |
| I.S. EN ISO 20028-2:2017 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017) |
| I.S. EN ISO 16396-2:2017 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 16396-2:2017) |
| ISO 27547-1:2010 | Plastics — Preparation of test specimens of thermoplastic materials using mouldless technologies — Part 1: General principles, and laser sintering of test specimens |
| ISO 20557-2:2018 | Plastics — Poly(phenylene ether) (PPE) moulding and extrusion materials — Part 2: Preparation of test specimen and determination of properties |
| DIN EN ISO 25137-2:2016-08 (Draft) | PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 25137-2:2009) |
| UNE-EN ISO 20753:2015 | Plastics - Test specimens (ISO 20753:2008) |
| ISO 7391-2:2006 | Plastics Polycarbonate (PC) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| EN 15860:2010 | Plastics - Thermoplastic semi-finished products for machining - Requirements and test methods |
| ASTM D 5592 : 1994 : R2002 : EDT 1 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| DIN EN ISO 7792-2:2013-03 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 7792-2:2012) |
| BS EN ISO 8986-2:2009 | Plastics. Polybutene-1 (PB-1) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 15103-2:2007 | Plastics. Poly(phenylene ether) (PPE) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 14910-2:2013 | Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Preparation of test specimens and determination of properties |
| ISO 15252-2:1999 | Plastics Epoxy powder moulding compounds (EP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 2898-2:2008 | Plastics. Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials Preparation of test specimens and determination of properties (ISO 2898-2:2008) |
| UNE-EN ISO 3673-2:2013 | Plastics - Epoxy resins - Part 2: Preparation of test specimens and determination of properties of crosslinked epoxy resins (ISO 3673-2:2012) |
| ISO 1872-2:2007 | Plastics Polyethylene (PE) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 14527-2:1999 | Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 7792-2:2012 | Plastics. Thermoplastic polyester (TP) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 10724-1:2001 | Plastics. Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) General principles and moulding of multipurpose test specimens |
| BS EN ISO 14530-2:2000 | Plastics. Unsaturated-polyester powder moulding compounds (UP-PMCs) Preparation of test specimens and determination of properties |
| BS EN ISO 15252-2:2000 | Plastics. Epoxy powder moulding compounds (EP-PMCs) Preparation of test specimens and determination of properties |
| DIN EN ISO 2898-2:2009-03 | PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN 62631-3-2:2016 | Dielectric and resistive properties of solid insulating materials - Part 3-2: Determination of resistive properties (DC Methods) - Surface resistance and surface resistivity |
| DIN EN ISO 14910-2:2013-06 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013) |
| DIN EN ISO 11403-2:2013-01 | Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012) |
| DIN EN ISO 11403-3:2002-02 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014) |
| DIN EN ISO 8986-2:2010-04 | PLASTICS - POLYBUTENE-1 (PB-1) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 11403-1:2003-09 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO 11403-1:2014) |
| NS-EN ISO 8256:2023 | Plastics - Determination of tensile-impact strength (ISO 8256:2023) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.