I.S. EN ISO 21003-3:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 3: FITTINGS
Hardcopy , PDF
11-17-2021
English
01-01-2008
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Material characteristics
5.1 Plastics fitting materials specified in reference
product standards
5.2 Plastics fitting materials not specified in reference
product standards
5.3 Metallic fitting material
5.4 Influence on water intended for human consumption
6 General characteristics
6.1 Appearance
6.2 Opacity
7 Geometrical characteristics
7.1 General
7.2 Dimensions of sockets for socket weld, electrofusion
and solvent-cemented fittings
7.3 Dimensions of metallic fittings
8 Mechanical characteristics of plastics fittings (internal
pressure test)
8.1 General
8.2 Plastics fitting materials specified in reference
product standards
8.3 Plastics fitting materials not specified in reference
product standards
9 Physical and chemical characteristics of plastics fittings
9.1 Plastics fitting materials specified in reference
product standards
9.2 Plastics fitting materials not specified in reference
product standards
9.3 Sealing elements
10 Performance requirements
11 Marking
11.1 General requirements
11.2 Minimum required marking
Annex A (normative) - List of reference product standards
Bibliography
Describes the characteristics of fittings for multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water - whether or not the water is intended for human consumption (domestic systems) or for heating systems - under specified design pressures and temperatures appropriate to the class of application.
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 21003-3:2008 | Identical |
| EN ISO 21003-3:2008 | Identical |
| EN 1254-3:1998 | Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes |
| ISO 15874-3:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 3: Fittings |
| ISO 15877-3:2009 | Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl chloride) (PVC-C) — Part 3: Fittings |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| BS 7291-2:2006 | Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings Specification for polybutylene (PB) pipes and associated fittings |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO 21003-5:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 5: Fitness for purpose of the system |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 15876-3:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 3: Fittings |
| ISO 1167-3:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components |
| ISO 21003-2:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes |
| ISO 21003-1:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 1: General |
| ISO 22391-3:2009 | Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 3: Fittings |
| BS 7291-4:1990 | Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings Specification for chlorinated polyvinyl chloride (PVC-C) pipes and associated fittings and solvent cement |
| ISO/TS 21003-7:2008 | Multilayer piping systems for hot and cold water installations inside buildings Part 7: Guidance for the assessment of conformity |
| ISO 15875-3:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 3: Fittings |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 7686:2005 | Plastics pipes and fittings — Determination of opacity |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.