I.S. EN 13000:2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Cranes - Mobile cranes
Hardcopy , PDF
05-31-2014
English
02-13-2010
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Safety requirements and/or protective measures
5 Verification
6 Information for use
7 Marking
Annex A (normative) - Examples of mobile crane types
Annex C (normative) - List of hazards
Annex D (normative) - Load effects of combined motions
Annex E (normative) - Crane operator's seat dimensions
Annex F (normative) - Rigid body stability: Load effects
due to acceleration
Annex G.1 (normative) - Noise test code for mobile cranes
Annex G.2 (normative) - Noise measurement, test report
Annex H (normative) - Limit values for structural and fine
grain steel types
Annex J.1 (normative) - Minimum requirements for
specification of hoist/derrick gears
Annex J.2 (normative) - Minimum requirements for
specification of slewing gears
Annex J.3 (normative) - Minimum requirements for
specification of travel gears
Annex J.4 (normative) - Minimum requirements for
specification of drums
Annex K.1 (normative) - Minimum requirements for the
specification of lifting hooks
Annex K.2 (normative) - Minimum requirements for
specification of sheaves
Annex K.3 (normative) - Minimum requirements for
specification of hook blocks
Annex K.4 (normative) - Minimum requirements for the
specification of hydraulic cylinders
Annex K.5 (normative) - Minimum requirements for the
specification of slew rings
Annex L (normative) - Proof of competence
Annex M (normative) - Test of steering systems for
off-road mobile cranes
Annex N.1 (informative) - Wind speed as a function of
Elevation
Annex N.2 (informative) - Impact pressure as a function
of elevation
Annex N.3 (informative) - Storm wind map of Europe
Annex N.4 (normative) - Simplified method to determine
the maximum allowed wind speed
Annex N.5 (informative) - Typical shapes and corresponding
Cw values
Annex P (normative) - Efficiency of sheave sets
Annex Q (informative) - Manufacturer's sign
Annex R (normative) - Certificate for wire rope, requirements
Annex S (normative) - Certificate for chain, requirements
Annex T (informative) - Test procedures: Selection of load
cases
Annex U (normative) - Test certificate
Annex V (informative) - Additional information of the
concept of the limiting and indicating device
Annex W (informative) - Selection of a suitable set of
crane standards for a given application
Annex ZA (informative) - Relation between this European
Standard and the Essential Requirements of
EU Directive 2006/42/EC
Bibliography
Pertains to the design, construction, installation of safety devices, information for use, maintenance and testing of mobile cranes as defined in ISO 4306-2.
| DevelopmentNote |
2010 Edition Re-Issued in May 2014 & incorporates AMD 1 2014. (06/2014)
|
| DocumentType |
Standard
|
| Pages |
114
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BS EN 13000 : 2010 | Identical |
| DIN EN 13000:2014-11 | Identical |
| NEN EN 13000 : 2010 + A1 2014 | Identical |
| NF EN 13000 : 2010 + A1 2014 | Identical |
| SN EN 13000+A1:2014 | Identical |
| ONORM EN 13000 : 2016 | Identical |
| NS EN 13000 : 2010 + A1 2014 | Identical |
| UNI EN 13000 : 2014 | Identical |
| EN 13000:2010+A1:2014 | Identical |
| NBN EN 13000 : 2010 + A1 2014 | Identical |
| UNE-EN 13000:2010 | Identical |
| I.S. 361:2013 | CODE OF PRACTICE FOR THE SAFE USE OF TOWER CRANES AND SELF-ERECTING CRANES |
| DIN 15403:1969-12 | LIFTING HOOKS FOR HOISTS; KNUCKLE THREADS |
| EN 854:2015 | Rubber hoses and hose assemblies - Textile reinforced hydraulic type - Specification |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| IEC 61672-2:2013+AMD1:2017 CSV | Electroacoustics - Sound level meters - Part 2: Pattern evaluation tests |
| ISO 4308-1:2003 | Cranes and lifting appliances Selection of wire ropes Part 1: General |
| ISO 11660-2:2015 | Cranes Access, guards and restraints Part 2: Mobile cranes |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| EN 856:2015 | Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification |
| EN 13557:2003+A2:2008 | Cranes - Controls and control stations |
| EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| ISO 5349-2:2001 | Mechanical vibration Measurement and evaluation of human exposure to hand-transmitted vibration Part 2: Practical guidance for measurement at the workplace |
| ISO 11660-1:2008 | Cranes — Access, guards and restraints — Part 1: General |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| EN 547-2:1996+A1:2008 | Safety of machinery - Human body measurements - Part 2: Principles for determining the dimensions required for access openings |
| EN ISO 6683:2008 | Earth-moving machinery - Seat belts and seat belt anchorages - Performance requirements and tests (ISO 6683:2005) |
| ISO 12480-1:1997 | Cranes — Safe use — Part 1: General |
| ISO 4306-1:2007 | Cranes — Vocabulary — Part 1: General |
| IEC 61310-2:2007 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| ISO 4310:2009 | Cranes — Test code and procedures |
| ISO 7096:2000 | Earth-moving machinery Laboratory evaluation of operator seat vibration |
| IEC 61000-6-2:2016 | Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
| ISO 3411:2007 | Earth-moving machinery Physical dimensions of operators and minimum operator space envelope |
| ISO 6683:2005 | Earth-moving machinery Seat belts and seat belt anchorages Performance requirements and tests |
| EN 61310-2:2008 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| EN ISO 3411:2007 | Earth-moving machinery - Physical dimensions of operators and minimum operator space envelope (ISO 3411:2007) |
| ISO 7250:1996 | Basic human body measurements for technological design |
| EN 14502-2:2005+A1:2008 | Cranes - Equipment for the lifting of persons - Part 2: Elevating control stations |
| EN 61672-2:2013/A1:2017 | ELECTROACOUSTICS - SOUND LEVEL METERS - PART 2: PATTERN EVALUATION TESTS (IEC 61672-2:2013/A1:2017) |
| ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
| ISO 5353:1995 | Earth-moving machinery, and tractors and machinery for agriculture and forestry Seat index point |
| ISO 8566-2:2016 | Cranes — Cabins and control stations — Part 2: Mobile cranes |
| EN 811 : 1996 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE LOWER LIMBS |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| ISO 13200:1995 | Cranes — Safety signs and hazard pictorials — General principles |
| EN 547-1:1996+A1:2008 | Safety of machinery - Human body measurements - Part 1: Principles for determining the dimensions required for openings for whole body access into machinery |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| ISO 4308-2:1988 | Cranes and lifting appliances Selection of wire ropes Part 2: Mobile cranes Coefficient of utilization |
| ISO 11662-1:1995 | Mobile cranes — Experimental determination of crane performance — Part 1: Tipping loads and radii |
| ISO 8686-1:2012 | Cranes — Design principles for loads and load combinations — Part 1: General |
| IEC 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
| EN 13586:2004+A1:2008 | Cranes - Access |
| EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
| DIN 15401-1:1982-11 | LIFTING HOOKS; SHANK HOOKS WITH A POINT; FORGINGS |
| EN ISO 7731:2008 | Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003) |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| EN ISO 4014:2011 | Hexagon head bolts - Product grades A and B (ISO 4014:2011) |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| EN 12644-1:2001+A1:2008 | Cranes - Information for use and testing - Part 1: Instructions |
| ISO 7731:2003 | Ergonomics Danger signals for public and work areas Auditory danger signals |
| ISO 7752-2:2011 | Cranes — Control layout and characteristics — Part 2: Basic arrangement and requirements for mobile cranes |
| ISO 3795:1989 | Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials |
| EN ISO 13732-1:2008 | Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006) |
| EN 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
| EN ISO 5353:1998 | Earth-moving machinery, and tractors and machinery for agriculture and forestry - Seat index point (ISO 5353:1995) |
| EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
| EN 13001-2:2014 | Crane safety - General design - Part 2: Load actions |
| ISO 10973:1995 | Cranes — Spare parts manual |
| EN 626-2:1996+A1:2008 | Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedures |
| EN 61672-1:2013 | Electroacoustics - Sound level meters - Part 1: Specifications |
| ISO 4301-2:2009 | Cranes Classification Part 2: Mobile cranes |
| ISO 4309:2010 | Cranes Wire ropes Care and maintenance, inspection and discard |
| EN 61000-6-2:2005/corrigendum:2005 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005) |
| EN ISO 5349-1:2001 | Mechanical vibration - Measurement and evaluation of human exposure to hand-transmitted vibration - Part 1: General requirements (ISO 5349-1:2001) |
| ISO 4305:2014 | Mobile cranes — Determination of stability |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN 842:1996+A1:2008 | Safety of machinery - Visual danger signals - General requirements, design and testing |
| EN 61000-6-4:2007/A1:2011 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS |
| EN ISO 6385:2016 | Ergonomics principles in the design of work systems (ISO 6385:2016) |
| ISO 8087:1985 | Mobile cranes Drum and sheave sizes |
| ISO 13849-2:2012 | Safety of machinery — Safety-related parts of control systems — Part 2: Validation |
| ISO 8995-3:2006 | Lighting of work places Part 3: Lighting requirements for safety and security of outdoor work places |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| ISO 6309:1987 | Fire protection — Safety signs |
| ISO 7296-2:1996 | Cranes Graphical symbols Part 2: Mobile cranes |
| IEC 61000-6-4:2006+AMD1:2010 CSV | Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments |
| ISO 2631-1:1997 | Mechanical vibration and shock — Evaluation of human exposure to whole-body vibration — Part 1: General requirements |
| ISO 3864-1:2011 | Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings |
| EN ISO 13849-2:2012 | Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012) |
| ISO 261:1998 | ISO general purpose metric screw threads — General plan |
| DIN 15400:1990-06 | LIFTING HOOKS - MATERIALS, MECHANICAL PROPERTIES, LIFTING CAPACITY AND STRESSES |
| EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
| EN 10025-6:2004+A1:2009 | Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition |
| EN 954-1 : 1996 | SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN ISO 7250 : 1997 | BASIC HUMAN BODY MEASUREMENTS FOR TECHNOLOGICAL DESIGN |
| ISO 5349-1:2001 | Mechanical vibration Measurement and evaluation of human exposure to hand-transmitted vibration Part 1: General requirements |
| EN 626-1:1994+A1:2008 | Safety of machinery - Reduction of risks to health from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers |
| DIN 15061-2:1977-08 | CRANES; GROOVE PROFILES FOR WIRE ROPE DRUMS |
| DIN 15401-2:1983-09 | LIFTING HOOKS FOR LIFTING APPLIANCES - SINGLE HOOKS - FINISHED PARTS WITH THREADED SHANK |
| EN 1005-3:2002+A1:2008 | Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation |
| EN 853:2015 | Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type - Specification |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| ISO 4301-1:2016 | Cranes — Classification — Part 1: General |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| ISO 12482-1:1995 | Cranes Condition monitoring Part 1: General |
| ISO 4306-2:1994 | Cranes — Vocabulary — Part 2: Mobile cranes |
| ISO 6385:2016 | Ergonomics principles in the design of work systems |
| ISO 8995-1:2002 | Lighting of work places Part 1: Indoor |
| ISO 11201:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| 1987/404/EEC : 1987 | COUNCIL DIRECTIVE OF 25 JUNE 1987 ON THE HARMONIZATION OF THE LAWS OF THE MEMBER STATES RELATING TO SIMPLE PRESSURE VESSELS |
| ISO 4014:2011 | Hexagon head bolts Product grades A and B |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.