EN 15162:2008
Current
The latest, up-to-date edition.
Machines and plants for mining and tooling of natural stone - Safety requirements for gang saws
05-21-2008
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
5.1 General
5.2 Protection against mechanical hazards
5.2.1 Locking the carriage
5.2.2 End run of blade frame
5.2.3 Hazard of belt breakage
5.2.4 Guards around motor and flywheel area
5.2.5 Slabs-holding device
5.2.6 Access to machine
5.2.7 Lifting and descent of blade frame and
carriage
5.2.8 Pump room for gang saw
5.2.9 System of distribution and collection
of the (abrasive) slurry
5.3 Electrical equipment and energy supply
5.3.1 General
5.3.2 Control panel
5.3.3 Start-up and mode selector
5.3.4 Starting procedures and sequence
5.3.5 Emergency stop
5.3.6 Safety-related parts of the control systems
5.3.7 Power failure
5.3.8 Motor and motor enclosure
5.3.9 Safety requirements related to electromagnetic
phenomena
5.3.10 Supply disconnecting devices
5.4 Hydraulic and pneumatic equipment
5.5 Ergonomic aspects
6 Verification of safety requirements and/or protective
measures
7 Information for use
7.1 General
7.2 Signal and warning devices
7.3 Instruction handbook
7.3.1 General
7.3.2 Description of the machine
7.3.3 Instructions for transport, handling and
storage of the machine and its dismountable
parts
7.3.4 Instructions for the installation and the
use of the machine
7.3.5 Maintenance instructions
7.3.6 Spare parts list
7.4 Marking
Annex ZA (informative) - Relationship between this European
Standard and the Essential
Requirements of EU Directive 98/37/EC
Annex ZB (informative) - Relationship between this European
Standard and the Essential
Requirements of EU Directive 2006/42/EC
Bibliography
This standard applies to monoblade or multiblade gang saws, as defined in 3.1, for cutting marble, granite, other types of natural stone, artificial or natural conglomerates and similar materials.This standard does not deal with noise as a significant hazard.This standard deals with all significant hazards, hazardous situations and events relevant to gang saw ma-chines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard deals with the hazards during transport, commissioning, use and maintenance.This document is not applicable to gang saws which are manufactured before the date of its publication as EN.
| Committee |
CEN/TC 151
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| NS EN 15162 : 1ED 2008 | Identical |
| NBN EN 15162 : 2008 | Identical |
| NF EN 15162 : 2008 | Identical |
| NEN EN 15162 : 2008 | Identical |
| SN EN 15162 : 2008 | Identical |
| PN EN 15162 : 2008 | Identical |
| I.S. EN 15162:2008 | Identical |
| DIN EN 15162:2008-10 | Identical |
| UNI EN 15162 : 2008 | Identical |
| BS EN 15162:2008 | Identical |
| UNE-EN 15162:2008 | Identical |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| ISO 14122-3:2016 | Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails |
| ISO 14122-1:2016 | Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| EN 1760-1:1997+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| ISO 14122-4:2016 | Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders |
| EN 1010-1:2004+A1:2010 | Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 1: Common requirements |
| EN ISO 14122-3:2016 | Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016) |
| EN 61496-1:2013/AC:2015 | SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 1: GENERAL REQUIREMENTS AND TESTS (IEC 61496-1:2012) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN ISO 14122-4:2016 | Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016) |
| EN ISO 14122-2:2016 | Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016) |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| IEC 61496-1:2012 | Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests |
| EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 1760-2:2001+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 14122-2:2016 | Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
| EN ISO 14122-1:2016 | Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.