BS ISO 16143-2:2014
Current
The latest, up-to-date edition.
Stainless steels for general purposes Corrosion-resistant semi-finished products, bars, rods and sections
Hardcopy , PDF
English
05-31-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Designation
5 Information to be supplied by the purchaser
6 Classification of grades
7 Requirements
8 Inspection, testing, and conformance of products
9 Marking
Annex A (informative) - Guidelines for further treatment
(including heat treatment) in fabrication
Annex B (informative) - Designations of the steels given
in Table 2 and of comparable grades covered
in ASTM, EN, JIS, and GB Standards
Annex C (informative) - Applicable dimensional standards
Bibliography
Defines the technical delivery conditions for semi-finished products, hot formed bars, rods, and sections for general purposes made of the most important corrosion-resistant stainless steel grades.
| Committee |
ISE/105
|
| DevelopmentNote |
Supersedes 12/30250149 DC. (06/2014)
|
| DocumentType |
Standard
|
| Pages |
48
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This part of ISO16143 specifies the technical delivery conditions for semi-finished products, hot formed bars, rods, and sections for general purposes made of the most important corrosion-resistant stainless steel grades.
NOTE 1 Throughout this part of ISO16143, the term “general purposes” means purposes other than the special purposes mentioned in the Bibliography.
NOTE 2 Heat-resistant steel grades can be found in ISO4955 and they can be used for corrosion-resistant purposes.
In addition to this part of ISO16143, the general technical delivery requirements of ISO404 are applicable.
This part of ISO16143 does not apply to components manufactured by further processing the product forms listed in the first paragraph above with quality characteristics altered as a result of such further processing.
| Standards | Relationship |
| ISO 16143-2:2014 | Identical |
| ISO 404:2013 | Steel and steel products — General technical delivery requirements |
| ISO 6929:2013 | Steel products — Vocabulary |
| ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
| ISO 20723:2004 | Structural steels — Surface condition of hot-rolled sections — Delivery requirements |
| ISO/TS 4949:2016 | Steel names based on letter symbols |
| ISO/TR 9769:1991 | Steel and iron Review of available methods of analysis |
| ISO 15510:2014 | Stainless steels — Chemical composition |
| EN 10056-2:1993 | Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and dimensions |
| ISO 16124:2015 | Steel wire rod — Dimensions and tolerances |
| EN 10279:2000 | Hot rolled steel channels - Tolerances on shape, dimensions and mass |
| ISO 1035-3:1980 | Hot-rolled steel bars — Part 3: Dimensions of flat bars |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| EN 10034:1993 | Structural steel I and H sections - Tolerances on shape and dimensions |
| ISO 1035-4:1982 | Hot-rolled steel bars — Part 4: Tolerances |
| EN 10024:1995 | Hot rolled taper flange I sections - Tolerances on shape and dimensions |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| EN 10060:2003 | Hot rolled round steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| ISO 1035-1:1980 | Hot-rolled steel bars — Part 1: Dimensions of round bars |
| EN 10017:2004 | Steel rod for drawing and/or cold rolling - Dimensions and tolerances |
| ISO 4955:2016 | Heat-resistant steels |
| ISO 3651-2:1998 | Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid |
| ISO 286-1:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
| ISO 10474:2013 | Steel and steel products — Inspection documents |
| ISO 1035-2:1980 | Hot-rolled steel bars — Part 2: Dimensions of square bars |
| ISO 6892-2:2011 | Metallic materials Tensile testing Part 2: Method of test at elevated temperature |
| EN 10061:2003 | Hot rolled hexagon steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| EN 10059:2003 | Hot rolled square steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| ASTM A 555/A555M : 2016 : REDLINE | Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods |
| EN 10055:1995 | Hot rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on shape and dimensions |
| ISO 377:2017 | Steel and steel products — Location and preparation of samples and test pieces for mechanical testing |
| ISO 14284:1996 | Steel and iron — Sampling and preparation of samples for the determination of chemical composition |
| ISO 9443:1991 | Heat-treatable and alloy steels Surface quality classes for hot-rolled round bars and wire rods Technical delivery conditions |
| ISO 6931-1:2016 | Stainless steels for springs Part 1: Wire |
| ISO 4954:1993 | Steels for cold heading and cold extruding |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.