BS EN ISO 14405-2:2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Geometrical product specifications (GPS). Dimensional tolerancing Dimensions other than linear sizes
Hardcopy , PDF
02-05-2019
English
12-31-2011
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principles and rules for indication of dimensions and
related tolerances
5 Units used in drawings for dimensions
6 Indication of tolerances for linear and angular
dimensions
7 Illustrations of ambiguous +/- tolerancing vs. unambiguous
geometrical tolerancing
8 Angular tolerancing
Annex A (informative) - Explanations and examples of the
ambiguity caused by using +/- tolerances for
dimensions other than linear size
Annex B (informative) - Relation to the GPS matrix model
Bibliography
Depicts the use of geometrical tolerancing for dimensions that are not linear sizes to avoid the ambiguity that the use of +/- tolerances on these dimensions causes.
| Committee |
TPR/1
|
| DevelopmentNote |
Supersedes BS ISO 406. (12/2011)
|
| DocumentType |
Standard
|
| Pages |
34
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN ISO 14405-2:2011 | Identical |
| ISO 14405-2:2011 | Identical |
| 13/30275718 DC : 0 | BS 8888 - TECHNICAL PRODUCT DOCUMENTATION AND SPECIFICATION |
| 16/30334592 DC : 0 | BS 8888 - TECHNICAL PRODUCT DOCUMENTATION AND SPECIFICATION |
| BS 8888:2017 | Technical product documentation and specification |
| BS 8888:2013 | Technical product documentation and specification |
| ISO/TR 14638:1995 | Geometrical product specification (GPS) Masterplan |
| ISO 8015:2011 | Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules |
| ISO/TS 17450-2:2002 | Geometrical product specifications (GPS) General concepts Part 2: Basic tenets, specifications, operators and uncertainties |
| ISO 5459:2011 | Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems |
| ISO 2692:2014 | Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 14253-1:2017 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications |
| ISO 8062-3:2007 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings |
| ISO 3040:2016 | Geometrical product specifications (GPS) Dimensioning and tolerancing Cones |
| ISO 81714-1:2010 | Design of graphical symbols for use in the technical documentation of products Part 1: Basic rules |
| ISO 2538:1998 | Geometrical Product Specifications (GPS) Series of angles and slopes on prisms |
| ISO 286-1:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
| ISO 14660-2:1999 | Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature |
| ISO/TS 17450-1:2005 | Geometrical product specifications (GPS) General concepts Part 1: Model for geometrical specification and verification |
| ISO 129-1:2004 | Technical drawings Indication of dimensions and tolerances Part 1: General principles |
| ISO 14660-1:1999 | Geometrical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions |
| ISO 14405-1:2016 | Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes |
| ISO 14253-2:2011 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification |
| ISO 13715:2017 | Technical product documentation — Edges of undefined shape — Indication and dimensioning |
| ISO 5458:1998 | Geometrical Product Specifications (GPS) Geometrical tolerancing Positional tolerancing |
| ISO/R 1938:1971 | ISO system of limits and fits Part II : Inspection of plain workpieces |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.