BS EN 13492:2013
Current
The latest, up-to-date edition.
Geosynthetic barriers. Characteristics required for use in the construction of liquid waste disposal sites, transfer stations or secondary containment
Hardcopy , PDF
English
07-31-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviations
4 Required characteristics and corresponding methods
of test
5 Evaluation of conformity
6 Marking
Annex A (normative) - Factory production control -
Factory production control scheme
Annex B (normative) - Durability of geosynthetic
barriers
Annex ZA (informative) - Clauses of this European
Standard addressing the provisions of the
EU Construction Products Directive
Bibliography
Defines the relevant characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, when used as fluid barriers in the construction of liquid waste disposal sites and in the construction of transfer stations and secondary containment for the storage of liquid waste on a waste disposal site only and the appropriate test methods to determine these characteristics.
| Committee |
B/553
|
| DevelopmentNote |
Supersedes 99/100964 DC. (01/2005) Supersedes 12/30267854 DC. (07/2013) Supersedes 16/30338126 DC. (05/2018)
|
| DocumentType |
Standard
|
| Pages |
44
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| SupersededBy | |
| Supersedes |
This European Standard specifies the relevant characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, when used as fluid barriers in the construction of liquid waste disposal sites and in the construction of transfer stations and secondary containment for the storage of liquid waste on a waste disposal site only and the appropriate test methods to determine these characteristics.
The intended use of these products is to control the leakage of fluids through the construction.
This document is not applicable to geotextiles or geotextile-related products.
This document provides for the evaluation of conformity of the product to this document.
This document defines requirements to be met by manufacturers and distributors with regard to the presentation of product properties.
| Standards | Relationship |
| UNI EN 13492 : 2013 | Identical |
| UNE-EN 13492:2013 | Identical |
| NF EN 13492 : 2013 | Identical |
| I.S. EN 13492:2013 | Identical |
| DIN EN 13492:2016-08 (Draft) | Identical |
| NBN EN 13492 : 2013 | Identical |
| ONORM EN 13492 : 2013 | Identical |
| EN 13492:2013 | Identical |
| DIN EN 13492:2013-11 | Identical |
| EN 13492:2018 | Identical |
| NEN EN 13492 : 2018 | Identical |
| NS EN 13492 : 2018 | Identical |
| EN 14576:2005 | Geosynthetics - Test method for determining the resistance of polymeric geosynthetic barriers to environmental stress cracking |
| PREN 16416 : DRAFT 2012 | GEOSYNTHETIC CLAY BARRIERS - DETERMINATION OF WATER FLUX INDEX - FLEXIBLE WALL PERMEAMETER METHOD AT CONSTANT HEAD |
| EN 14575:2005 | Geosynthetic barriers - Screening test method for determining the resistance to oxidation |
| EN 14150:2006 | Geosynthetic barriers - Determination of permeability to liquids |
| ISO 13438:2004 | Geotextiles and geotextile-related products Screening test method for determining the resistance to oxidation |
| EN ISO 10319:2015 | Geosynthetics - Wide-width tensile test (ISO 10319:2015) |
| ISO 527-4:1997 | Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| CEN/TS 14418:2014 | Geosynthetic Barriers - Test method for the determination of the influence of freezing-thawing cycles on the permeability of clay geosynthetic barriers |
| ISO 10320:1999 | Geotextiles and geotextile-related products Identification on site |
| ISO 12236:2006 | Geosynthetics — Static puncture test (CBR test) |
| EN 1849-2:2009 | Flexible sheets for waterproofing - Determination of thickness and mass per unit area - Part 2: Plastic and rubber sheets |
| EN ISO 527-4:1997 | Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotopic fibre-reinforced plastic composites (ISO 527-4:1997) |
| EN 495-5:2013 | Flexible sheets for waterproofing - Determination of foldability at low temperature - Part 5: Plastic and rubber sheets for roof waterproofing |
| ISO 9863-1:2016 | Geosynthetics Determination of thickness at specified pressures Part 1: Single layers |
| EN 14151:2010 | Geosynthetics - Determination of burst strength |
| 89/106/EEC : 1988 | COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS |
| ISO 10319:2015 | Geosynthetics — Wide-width tensile test |
| EN 12224:2000 | Geotextiles and geotextile-related products - Determination of the resistance to weathering |
| EN ISO 10773:2011 | Clay geosynthetic barriers - Determination of permeability to gases (ISO 10773:2011) |
| EN ISO 10318:2005 | Geosynthetics - Terms and definitions (ISO 10318:2005) |
| ISO 34-1:2015 | Rubber, vulcanized or thermoplastic Determination of tear strength Part 1: Trouser, angle and crescent test pieces |
| EN 12311-2:2013 | Flexible sheets for waterproofing - Determination of tensile properties - Part 2: Plastic and rubber sheets for roof waterproofing |
| EN ISO 527-1:2012 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
| ISO 9862:2005 | Geosynthetics — Sampling and preparation of test specimens |
| EN ISO 10320:1999 | Geotextiles and geotextile-related products - Identification on site (ISO 10320:1999) |
| EN 12311-1:1999 | Flexible sheets for waterproofing - Part 1: Bitumen sheets for roof waterproofing - Determination of tensile properties |
| EN 1844:2013 | Flexible sheets for waterproofing - Determination of resistance to ozone - Plastic and rubber sheets for roof waterproofing |
| EN 12310-1:1999 | Flexible sheets for waterproofing - Part 1: Bitumen sheets for waterproofing - Determination of resistance to tearing (nail shank) |
| EN 14414:2004 | Geosynthetics - Screening test method for determining chemical resistance for landfill applications |
| ISO 12957-1:2005 | Geosynthetics Determination of friction characteristics Part 1: Direct shear test |
| ASTM D 1603 : 2014 : REDLINE | Standard Test Method for Carbon Black Content in Olefin Plastics |
| EN 1109:2013 | Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination of flexibility at low temperature |
| CEN/TS 14417:2014 | Geosynthetic barriers - Test method for the determination of the influence of wetting-drying cycles on the permeability of clay geosynthetic barriers |
| ASTM D 696 : 2016 : REDLINE | Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer |
| EN ISO 12957-2:2005 | Geosynthetics - Determination of friction characteristics - Part 2: Inclined plane test (ISO 12957-2:2005) |
| EN ISO 11358:1997 | Plastics - Thermogravimetry (TG) of polymers - General principles (ISO 11358:1997) |
| ISO 12957-2:2005 | Geosynthetics — Determination of friction characteristics — Part 2: Inclined plane test |
| EN 12225:2000 | Geotextiles and geotextile-related products - Method for determining the microbiological resistance by a soil burial test |
| EN 14196:2016 | Geosynthetics - Test methods for measuring mass per unit area of clay geosynthetic barriers |
| EN ISO 9864:2005 | Geosynthetics - Test method for the determination of mass per unit area of geotextiles and geotextile-related products (ISO 9864:2005) |
| ISO 11358:1997 | Plastics Thermogravimetry (TG) of polymers General principles |
| EN ISO 9863-1:2016 | Geosynthetics - Determination of thickness at specified pressures - Part 1: Single layers (ISO 9863-1:2016) |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO/TR 13434:1998 | Geotextiles and geotextile-related products Guidelines on durability |
| ISO 10773:2011 | Clay geosynthetic barriers Determination of permeability to gases |
| EN 1849-1:1999 | Flexible sheets for waterproofing - Determination of thickness and mass per unit area - Part 1: Bitumen sheets for roof waterproofing |
| ISO 10318:2005 | Geosynthetics Terms and definitions |
| EN ISO 12236:2006 | Geosynthetics - Static puncture test (CBR test) (ISO 12236:2006) |
| ISO 527-3:1995 | Plastics Determination of tensile properties Part 3: Test conditions for films and sheets |
| ISO 9864:2005 | Geosynthetics — Test method for the determination of mass per unit area of geotextiles and geotextile-related products |
| EN ISO 9862:2005 | Geosynthetics - Sampling and preparation of test specimens (ISO 9862:2005) |
| CEN/TS 14416:2014 | Geosynthetic barriers - Test method for determining the resistance to roots |
| EN 14415:2004 | Geosynthetic barriers - Test method for determining the resistance to leaching |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.