ASTM F 3125/F3125M : 2019 : EDT 2
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength
Hardcopy , PDF
02-28-2022
English
09-23-2020
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
F 16
|
| DocumentType |
Standard
|
| Pages |
14
|
| ProductNote |
ε2NOTE—Sections16.1.4andA2.7.2.1were editorially corrected in September 2020.
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers chemical, physical and mechanical requirements for quenched and tempered bolts manufactured from steel and alloy steel, in inch and metric dimensions, in two strength grades, two types and two styles.
1.1.1This specification is a consolidation and replacement of six ASTM standards, including; A325, A325M, A490, A490M, F1852 and F2280.
1.1.2This consolidated standard is to ensure alignment between standards with the same intended end use and to simplify the use and maintenance of structural bolt specifications.
1.2Intended Use:
1.2.1Bolts manufactured under this specification are intended for use in structural connections covered in the Specification for Structural Joints Using High-Strength Bolts, as approved by the Research Council on Structural Connections.
1.2.2Bolts in this specification are furnished in sizes from 1/2to 1-1/2in. inclusive and from M12 to M36 inclusive.
1.3Classification, Table 1:
1.3.1Bolts are designated by grade, which indicates inch or metric strength and style.
1.3.2Bolts are designated by type denoting raw material chemical composition.
1.3.3Bolts are designated by style denoting Heavy Hex bolts or “Twist-Off” Style assemblies.
1.4Terms used in this specification are defined in F1789.
1.5Units—The values stated in either SI units or inch pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.6Table footnotes are requirements. Notes are advisory.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM A 563/A563M : 2021 : REV A | Standard Specification for Carbon and Alloy Steel Nuts (Inch and Metric) |
| ASTM F 3393 : 2020 : EDT 1 | Zinc-Flake Coating Systems for Fasteners |
| ASTM A 36/A36M : 2019 | Standard Specification for Carbon Structural Steel |
| ASTM B 695 : 2021 | Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel |
| ASTM A 354 : 2017 : EDT 2 | Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners |
| ASTM F 606/F606M : 2019 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets |
| ASTM F 1789 : 2017 : REV A | Standard Terminology for F16 Mechanical Fasteners |
| ASTM E 709 : 2015 | Standard Guide for Magnetic Particle Testing |
| ASTM B 695 : 2004 : R2016 | Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel |
| ASTM E 709 : 2021 | Standard Guide for Magnetic Particle Testing |
| ASTM A 751 : 2021 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
| ASTM B 695 : 2021 | Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel |
| ASTM E 1444/E1444M : 2021 | Standard Practice for Magnetic Particle Testing for Aerospace |
| ASTM F 1789 : 2017 : REV A : EDT 1 | Standard Terminology for F16 Mechanical Fasteners |
| ASTM A 563M : 2007 : R2013 | Standard Specification for Carbon and Alloy Steel Nuts (Metric) (Withdrawn 2021) |
| ASTM E 1444/E1444M : 2020 | Standard Practice for Magnetic Particle Testing for Aerospace |
| ASTM A 563 : 2015 | Standard Specification for Carbon and Alloy Steel Nuts |
| ASTM A 751 : 2020 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
| ASTM E 1444/E1444M : 2016 : EDT 1 | Standard Practice for Magnetic Particle Testing |
| ASTM F 606/F606M : 2021 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets |
| ASTM F 1789 : 2002 | Standard Terminology of F16 Mechanical Fasteners |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.