ASTM F 1498 : 2000
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
Hardcopy , PDF
11-11-2014
English
04-10-2000
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
F 17
|
| DocumentType |
Standard
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 This specification covers dimensions and gaging of taper pipe threads used on threaded plastic pipe and fittings.
1.2 Threads meeting this specification shall only be used on those plastic materials deemed suitable by the manufacturer.
1.3 Specialty threads or threads not requiring a leak-tight joint are not covered in this specification.
Note 1-The terms "wrench makeup" and "wrench tight" are standard terminology for tightness and do not imply using a pipe wrench or other tools which would damage plastic pipe and fittings.1.4 Thread Designations -The type of pipe threads included in this specification are designated by specifying in sequence the nominal pipe size, number of threads per inch, and the thread series symbols as follows in accordance with ANSI/ASME B1.20.1: 3/8-18 NPT. For left-hand threads add LH to the designation, otherwise right-hand threads will be understood. For example: 3/8-18 NPT-LH.
1.4.1 Each of these letters in the symbol has a definite significance as follows:
N = National (American Standard) P = Pipe T = Taper1.5 The values stated in inch-pound units are to be regarded as the standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see 7.2.1 and 8.3.
| ASTM D 2949 : 2018 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 2665 : 2014 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM F 3371 : 2019 | Standard Specification for Polyolefin Pipe and Fittings for Drainage, Waste, and Vent Applications |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2609 : 2015 | Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe |
| ASTM D 2846/D2846M : 2019 : REV A | Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems |
| ASTM F 2135 : 2001 : R2017 : EDT 1 | Standard Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings |
| ASTM F 645 : 2018 : REV B | Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems |
| ASTM D 2749 : 2013 | Standard Symbols for Dimensions of Plastic Pipe Fittings (Withdrawn 2022) |
| ASTM F 2618 : 2019 | Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems |
| ASTM F 437 : 2015 | Standard Specification for Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 |
| ASTM D 2467 : 2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
| ASTM F 438 : 2017 | Standard Specification for Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40 |
| ASTM D 2661 : 2014 : EDT 1 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM F 2735 : 2018 | Standard Specification for Plastic Insert Fittings For SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing |
| ASTM F 1673 : 2010 : R2016 | Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems |
| ASTM D 2464 : 2015 | Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
| ASTM F 1901 : 2016 | Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems |
| ASTM F 439 : 2013 | Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 |
| ASTM D 2466 : 2017 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 |
| ASTM F 2159 : 2019 | Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing |
| ASTM D 3311 : 2017 | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM F 628 : 2012 : EDT 3 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core (Withdrawn 2021) |
| ASTM F 1412 : 2016 | Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems |
| ASTM F 409 : 2017 | Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings |
| ASTM F 1970 : 2019 | Standard Specification for Special Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems |
| ASTM F 2390 : 2012 : R2017 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.