ASTM E 659 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Autoignition Temperature of Chemicals
Hardcopy , PDF
05-26-2023
English
09-25-2015
1.1 This test method covers the determination of hot- and cool-flame autoignition temperatures of a liquid chemical in air at atmospheric pressure in a uniformly heated vessel.
Committee |
E 27
|
DocumentType |
Test Method
|
Pages |
7
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers the determination of hot- and cool-flame autoignition temperatures of a liquid chemical in air at atmospheric pressure in a uniformly heated vessel.
Note 1:Within certain limitations, this test method can also be used to determine the autoignition temperature of solid chemicals which readily melt and vaporize at temperatures below the test temperature and for chemicals that are gaseous at atmospheric pressure and temperature.
Note 2:After a round robin study, Test Method D2155 was discontinued, and replaced by Test Method E659 in 1978. See also Appendix X2.
1.2This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.
ASTM D 8211 : 2021 | Standard Test Method for Hot Surface Ignition Temperature of Gases on Flat Surface |
ASTM D 2878 : 2021 | Standard Test Method for Estimating Apparent Vapor Pressures and Molecular Weights of Lubricating Oils |
ASTM D 7665 : 2022 | Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids |
ASTM D 7826 : 2022 | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
ASTM C 647 : 2019 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
ASTM D 7863 : 2022 | Standard Guide for Evaluation of Convective Heat Transfer Coefficient of Liquids |
ASTM C 1696 : 2020 | Standard Guide for Industrial Thermal Insulation Systems |
ASTM E 1445 : 2008 : R2015 | Standard Terminology Relating to Hazard Potential of Chemicals |
ASTM D 5372 : 2020 | Standard Guide for Evaluation of Hydrocarbon Heat Transfer Fluids |
ASTM E 1491 : 2006 : R2019 | Standard Test Method for Minimum Autoignition Temperature of Dust Clouds |
CEI EN IEC 60335-2-40:2024 | Household and similar electrical appliances - Safety - Part 2: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers |
ASTM D 2883 : 1995 : R2000 : EDT 1 | Standard Test Method for Reaction Threshold Temperature of Liquid and Solid Materials |
ASTM D 2155 : 2012 | Standard Test Method for Determination of Fire Resistance of Aircraft Hydraulic Fluids by Autoignition Temperature |
ASTM D 2883 : 1995 | Standard Test Method for Reaction Threshold Temperature of Liquid and Solid Materials |
ASTM D 2155 : 1966 : R1976 | Method of Test for Autoignition Temperature of Liquid Petroleum Products (Withdrawn 1980) |
ASTM D 2883 : 1995 : R2005 | Standard Test Method for Reaction Threshold Temperature of Liquid and Solid Materials |
ASTM D 2155 : 2018 | Standard Test Method for Determination of Fire Resistance of Aircraft Hydraulic Fluids by Autoignition Temperature |
ASTM D 2883 : 1995 : R2009 | Standard Test Method for Reaction Threshold Temperature of Liquid and Solid Materials (Withdrawn 2016) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.