ASTM D 2794 : 1993 : R2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
Hardcopy , PDF
11-11-2014
English
06-01-2004
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 06.01, 2017 Describes a procedure for rapidly deforming by impact a coating film and its substrate and for evaluating the effect of such deformation.
| Committee |
D 01
|
| DocumentType |
Test Method
|
| Pages |
3
|
| ProductNote |
Reconfirmed 2004
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method covers a procedure for rapidly deforming by impact a coating film and its substrate and for evaluating the effect of such deformation.
1.2 This test method should be restricted to testing in only one laboratory when numerical values are used because of the poor reproducibility of the method. Interlaboratory agreement is improved when ranking is used in place of numerical values.
1.3 This standard does not purport to address the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM E 1795 : 2017 | Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| ASTM D 3730 : 2017 | Standard Guide for Testing High-Performance Interior Architectural Wall Coatings |
| ASTM D 3794 : 2018 | Standard Guide for Testing Coil Coatings |
| ASTM F 2408 : 2016 | Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular Pickets |
| ASTM D 5420 : 2016 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| ASTM D 6665 : 2009 : R2014 | Standard Practice for Evaluation of Aging Resistance of Pre-stressed Prepainted Metal in a Boiling Water Test |
| ASTM D 6905 : 2003 : R2012 | Standard Test Method for Impact Flexibility of Organic Coatings |
| ASTM D 3732 : 1982 : R2017 | Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings |
| ASTM D 8161 : 2017 | Standard Test Method for Impact Resistance of Thermoplastic Pavement Marking Materials over a Highway Substrate by Means of a Striker Impacted by a Falling Weight |
| ASTM E 2924 : 2014 | Standard Practice for Intumescent Coatings |
| ASTM E 1797 : 2012 : R2017 : EDT 1 | Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| ASTM D 6577 : 2015 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM D 7230 : 2006 : R2013 | Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates |
| ASTM D 7270 : 2007 : R2013 | Standard Guide for Environmental and Performance Verification of Factory-Applied Liquid Coatings |
| ASTM A 742/A742M : 2018 | Standard Specification for Steel Sheet, Metallic Coated and Polymer Precoated for Corrugated Steel Pipe |
| ASTM D 4956 : 2019 | Standard Specification for Retroreflective Sheeting for Traffic Control |
| ASTM D 3451 : 2006 : R2017 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM D 16 : 2019 | Standard Terminology for Paint, Related Coatings, Materials, and Applications |
| ASTM F 2589 : 2016 | Standard Specification for Ornamental Fences Employing Steel Tubular Pickets |
| ASTM A 755/A755M : 2018 | Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products |
| ASTM D 823 : 1995 | Standard Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related Products on Test Panels |
| ASTM D 609 : 2017 : REDLINE | Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products |
| ASTM D 1186 : 2001 | Standard Test Methods for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base (Withdrawn 2006) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.