SAE AMS3144
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Primer, Anodic Electrodeposition for Aircraft Applications
Hardcopy , PDF
English
27-11-2012
21-10-2019
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. ACKNOWLEDGMENT
7. REJECTIONS
8. NOTES
Specifies the requirements for a waterborne, corrosion inhibiting, chemical and solvent resistant, anodic electrodeposition epoxy primer capable of curing at 200 to 210 degrees F (93 to 99 degrees C).
| DocumentType |
Standard
|
| Pages |
17
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy |
This specification establishes the requirements for a waterborne, corrosion inhibiting, chemical and solvent resistant, anodic electrodeposition epoxy primer capable of curing at 200 to 210 °F (93 to 99 °C).
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| FED-STD-313 Revision D:1996 | Material Safety Data, Transportation Data, and Disposal Data for Hazardous Materials Furnished to Government Activities |
| SAE AMSS8802D | Sealing Compound, Fuel Resistant, Integral Fuel Tanks and Fuel Cell Cavities |
| SAE AMS1640B | Corrosion Removing Compound For Aircraft Surfaces |
| MIL-PRF-81733 Revision D:1998 | Sealing and Coating Compound, Corrosion Inhibitive |
| MIL-PRF-7808 Revision L:1997 | Lubricating Oil, Aircraft Turbine Engine, Synthetic Base |
| MIL-PRF-85285 Revision E:2012 | Topcoat, Aircraft and Support Equipment |
| SAE AMSQQA250/4B | Aluminum Alloy 2024, Plate and Sheet |
| ASTM G 85 : 2011 : REDLINE | Standard Practice for Modified Salt Spray (Fog) Testing |
| MIL-PRF-23377 Revision K:2012 | Primer Coatings: Epoxy, High-Solids |
| SAE AS5127/1C | Aerospace Standard Test Methods for Aerospace Sealants Two-Component Synthetic Rubber Compounds |
| SAE AMS3277J | Sealing Compound, Polythioether Rubber Fast Curing for Integral Fuel Tanks and General Purpose, Intermittent Use to 360 °F (182 °C) |
| MIL-DTL-5541 Revision F:2006 | Chemical Conversion Coatings on Aluminum and Aluminum Alloys |
| TT-R-2918 Revision A:2001 | Remover, Paint, No Hazardous Air Pollutants (HAPS) |
| ASTM D 1974 : 1998 | Standard Practice for Methods of Closing, Sealing, and Reinforcing Fiberboard Boxes |
| ASTM D 2247 : 2015 : REDLINE | Standard Practice for Testing Water Resistance of Coatings in 100 % Relative Humidity |
| MIL-PRF-23699 Revision G:2014 | Lubricating Oil, Aircraft Turbine Engine, Synthetic Base, NATO Code Numbers: O-152, O-154, O-156, and O-167 |
| ISO 11890-1:2007 | Paints and varnishes — Determination of volatile organic compound (VOC) content — Part 1: Difference method |
| SAE AMSQQA250/5B | Aluminum Alloy Alclad 2024, Plate and Sheet |
| CFR 29(PT1910.1000 TO END) : 0 | LABOR - OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR |
| MIL A 8625 : F | ANODIC COATINGS FOR ALUMINUM AND ALUMINUM ALLOYS |
| ASTM D 7091 : 2013 : REDLINE | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| SAE AMS2629E | Fluid, Jet Reference |
| SAE AS1241D | Fire Resistant Phosphate Ester Hydraulic Fluid for Aircraft |
| ASTM D 2794 : 1993 | TEST METHOD FOR RESISTANCE OF ORGANIC COATINGS TO THE EFFECTS OF RAPID DEFORMATION (IMPACT) |
| MIL-PRF-83282 Revision D:1997 | Hydraulic Fluid, Fire Resistant, Synthetic Hydrocarbon Base, Metric, NATO Code Number H-537 |
| SAE AMS2825B | Material Safety Data Sheets |
| MIL-PRF-85582 Revision E:2012 | PRIMER COATINGS: EPOXY, WATERBORNE |
| FED-STD-141 Revision D:2001 | Paint, Varnish, Lacquer and Related Materials: Methods of Inspection, Sampling and Testing |
| ASTM D 522 : 1993 : REV A | Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings |
| ASTM D 3359 : 2017 : REDLINE | Standard Test Methods for Rating Adhesion by Tape Test |
| ASTM D 329 : 2007 | Standard Specification for Acetone |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.