I.S. EN 10149-1:2013
Current
The latest, up-to-date edition.
HOT ROLLED FLAT PRODUCTS MADE OF HIGH YIELD STRENGTH STEELS FOR COLD FORMING - PART 1: GENERAL TECHNICAL DELIVERY CONDITIONS
Hardcopy , PDF
English
01-01-2013
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Information to be supplied by the purchaser
5 Dimensions, mass and tolerances
6 Classification and designation
7 Technical requirements
8 Inspection and testing
9 Marking
10 Disputes
11 Options
Bibliography
Describes requirements for flat products made of weldable, hot-rolled, high yield strength alloy quality and special steels for cold forming.
| DocumentType |
Standard
|
| Pages |
19
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| EN 10149-1:2013 | Identical |
| NEN EN 10149-1 : 2013 | Identical |
| NS EN 10149-1 : 2013 | Identical |
| SN EN 10149-1 : 2013 | Identical |
| NF EN 10149-1 : 2013 | Identical |
| BS EN 10149-1:2013 | Identical |
| NBN EN 10149-1 : 2013 | Identical |
| UNE-EN 10149-1:2014 | Identical |
| UNI EN 10149-1 : 2013 | Identical |
| EN 10052:1993 | Vocabulary of heat treatment terms for ferrous products |
| EN 10162:2003 | Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances |
| EN 10048:1996 | Hot rolled narrow steel strip - Tolerances on dimensions and shape |
| EN 10051:2010 | Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape |
| EN 10079:2007 | Definition of steel products |
| EN 10025-4:2004 | Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| EN ISO 377:2017 | Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2017) |
| EN ISO 643:2012 | Steels - Micrographic determination of the apparent grain size (ISO 643:2012) |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| EN 10149-2:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels |
| EN 10168:2004 | Steel products - Inspection documents - List of information and description |
| EN ISO 2566-1:1999 | Steel - Conversion of elongation values - Part 1: Carbon and low alloy steels (ISO 2566-1:1984) |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| EN 10210-1:2006 | Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| EN 10163-2:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats |
| ISO 7438:2016 | Metallic materials Bend test |
| EN 10021:2006 | General technical delivery conditions for steel products |
| ISO 2566-1:1984 | Steel Conversion of elongation values Part 1: Carbon and low alloy steels |
| EN 10025-5:2004 | Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 643:2012 | Steels Micrographic determination of the apparent grain size |
| EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
| EN 10025-6:2004+A1:2009 | Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition |
| EN 10020:2000 | Definition and classification of grades of steel |
| CEN/TR 10347:2006 | Guidance for forming of structural steels in processing |
| EN ISO 148-1:2016 | Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016) |
| EN 10160:1999 | Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) |
| EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| ISO 377:2017 | Steel and steel products — Location and preparation of samples and test pieces for mechanical testing |
| EN 10149-3:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Technical delivery conditions for normalized or normalized rolled steels |
| EN ISO 7438:2016 | Metallic materials - Bend test (ISO 7438:2016) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.