DIN EN 13476-1:2015-11 (Draft)
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
Hardcopy , PDF
01-11-2018
German
01-01-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Vorwort
Einleitung
1 Anwendungsbereich
2 Normative Verweisungen
3 Begriffe, Symbole und Abkürzungen
3.1 Begriffe
3.1.1 Allgemeine Begriffe
3.1.2 Geometrische Begriffe
3.2 Symbole und Abkürzungen
4 Werkstoff
4.1 Allgemeines
4.2 Verwendung von anderen Werkstoffen als Neumaterial
4.3 Befestigungselemente für Dichtringe
4.4 Dichtringe
4.5 Heizelement-Stumpf-, Extrusions- und
Heizwendelschweissverbindungen
5 Bezeichnung von Wandaufbauten
6 Beschaffenheit und Farbe
6.1 Beschaffenheit
6.2 Farbe
7 Geometrische Eigenschaften
8 Formstückarten
8.1 Allgemeines
8.2 Konstruktionslängen von Formstücken
9 Auf Prüfverfahren und Eigenschaften bezogene
Leistungsfähigkeit des Systems
10 Kennzeichnung
10.1 Darstellung
10.2 Kennzeichnungsvorgang
10.3 Grösse der Kennzeichnung
Anhang A (informativ) Eigenschaften von Rohren und
Formstücken aus PVC-U, PP und PE
A.1 Allgemeines
A.2 Werkstoffeigenschaften
A.3 Chemikalienbeständigkeit
A.4 Abriebfestigkeit
A.5 Wandrauheit
Anhang B (informativ) Statische Berechnung
B.1 Allgemeines
B.2 Auf praktischen Erfahrungen
beruhende statische Berechnung
B.3 Statische Berechnung, beruhend
auf einer Konstruktionsberechnung
B.4 Auswahl der Steifigkeit oder
Klasse eines Formstückes
Anhang C (informativ) Bestellinformationen für Rohre und
zugehörige
Anhang D (informativ) Leitfaden für die Reinigung von
Kunststoff-Rohren
D.1 Einleitung
D.2 Reinigung und Entfernen von Verstopfungen
D.2.1 Auswahl der richtigen Ausrüstung
D.2.2 Vergleich der Verfahren
D.3 Schlussfolgerungen aus unabhängigen
Hochdruckspülversuchen
D.3.1 Bewertung von Effektivität
und Wirkung
D.3.2 Prüfung von Kunststoff-Rohren
D.3.3 Prüfungen der Beseitigung von
Verstopfungen
D.4 Ergänzende Reinigungsverfahren
D.5 Empfehlungen für grundlegende
Verfahrensweisen bei Hochdruckspülreinigung
Literaturhinweise
This standard is included in DIN Handbook 88. Describes the definitions and general requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are to be used for non-pressure underground drainage and sewerage systems.
| DevelopmentNote |
Supersedes DIN 19568-100. (09/2006) DRAFT 2016 issued in November 2016. (11/2016)
|
| DocumentType |
Draft
|
| Pages |
57
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| SN EN 13476-1 : 2007 | Identical |
| ONORM EN 13476-1 : 2008 | Identical |
| NBN EN 13476-1 : 2007 | Identical |
| UNI EN 13476-1 : 2008 | Identical |
| NF EN 13476-1 : 2007 | Identical |
| NS EN 13476-1 : 1ED 2007 | Identical |
| UNE-EN 13476-1:2007 | Identical |
| BS EN 13476-1:2007 | Identical |
| I.S. EN 13476-1:2007 | Identical |
| EN 13476-1:2018 | Identical |
| NEN EN 13476-1 : 2018 | Identical |
| DIN 1986-4:2019-08 | DRAINAGE SYSTEMS ON PRIVATE GROUND - PART 4: FIELDS OF APPLICATION OF SEWAGE PIPES AND FITTINGS OF DIFFERENT MATERIALS |
| DIN HDBK 88 : 11ED 2016 | ENTWAESSERUNGSKANALARBEITEN, DRUCKROHRLEITUNGSARBEITEN AUSSERHALB VON GEBAEUDEN, DRAEN- UND VERSICKERARBEITEN VOB/STLB-BAU - VOB TEIL C: ATV DIN 18299, ATV DIN 18306, ATV DIN 18307, ATV DIN 18308 |
| DIN 16961-2:2010-03 | THERMOPLASTICS PIPES AND FITTINGS WITH PROFILED WALL AND SMOOTH PIPE INSIDE - PART 2: TECHNICAL DELIVERY SPECIFICATIONS |
| DIN 16917-1:2015-10 | PIPES AND FITTINGS MADE OF THERMOPLASTIC MATERIALS WITH PROFILED WALL AND SMOOTH PIPE INSIDE - LARGE PIPES OVER DN 1200 FOR UNDERGROUND INSTALLATION - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS |
| DIN 16961-1:2011-01 | THERMOPLASTICS PIPES AND FITTINGS WITH PROFILED WALL AND SMOOTH PIPE INSIDE - PART 1: DIMENSIONS |
| DIN 1986-4:2011-12 | DRAINAGE SYSTEMS ON PRIVATE GROUND - PART 4: FIELDS OF APPLICATION OF SEWAGE PIPES AND FITTINGS OF DIFFERENT MATERIALS |
| EN 1277:2003 | Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints |
| EN 295-3:2012 | Vitrified clay pipe systems for drains and sewers - Part 3: Test methods |
| ISO 580:2005 | Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| ISO/TR 10358:1993 | Plastics pipes and fittings Combined chemical-resistance classification table |
| ISO 6259-2:1997 | Thermoplastics pipes Determination of tensile properties Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly (vinyl chloride) (PVC-C) and high-impact poly (vinyl chloride) (PVC-HI) |
| EN 1295-1:1997 | Structural design of buried pipelines under various conditions of loading - Part 1: General requirements |
| ISO 12091:1995 | Structured-wall thermoplastics pipes Oven test |
| EN 1411:1996 | Plastics piping and ducting systems - Thermoplastics pipes - Determination of resistance to external blows by the staircase method |
| EN ISO 9967:2016 | Thermoplastics pipes - Determination of creep ratio (ISO 9967:2016) |
| EN 728:1997 | Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 265-1:1988 | Pipes and fittings of plastics materials Fittings for domestic and industrial waste pipes Basic dimensions: Metric series Part 1: Unplasticized poly(vinyl chloride) (PVC-U) |
| EN 1055:1996 | Plastics piping systems - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for resistance to elevated temperature cycling |
| EN ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) |
| ISO/TR 7620:2005 | Rubber materials — Chemical resistance |
| EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| EN 14654-1:2014 | Management and control of operational activities in drain and sewer systems outside buildings - Part 1: Cleaning |
| EN ISO 6259-1:2015 | Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015) |
| CEN/TR 14920:2005 | Jetting resistance of drain and sewer pipes - Moving jet test method |
| EN 12061:1999 | Plastics piping systems - Thermoplastics fittings - Test method for impact resistance |
| ISO 6259-1:2015 | Thermoplastics pipes Determination of tensile properties Part 1: General test method |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| EN 476:2011 | General requirements for components used in drains and sewers |
| EN 1979:1999 | Plastics piping and ducting systems - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam |
| ISO 472:2013 | Plastics — Vocabulary |
| EN 14758-1:2012 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system |
| EN 12666-1:2005+A1:2011 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| EN ISO 9969:2016 | Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016) |
| EN 744:1995 | Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method |
| EN ISO 580:2005 | Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005) |
| EN 1401-1:2009 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| EN 580:2003 | Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for the resistance to dichloromethane at a specified temperature (DCMT) |
| EN 14741:2006 | Thermoplastics piping and ducting systems - Joints for buried non-pressure applications - Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure |
| EN 1610:2015 | Construction and testing of drains and sewers |
| ISO 9967:2016 | Thermoplastics pipes Determination of creep ratio |
| EN 1053:1995 | Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test method for watertightness |
| ISO 6259-3:2015 | Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes |
| EN ISO 2505:2005 | Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505:2005) |
| ISO 13967:2009 | Thermoplastics fittings Determination of ring stiffness |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| ISO 9969:2016 | Thermoplastics pipes Determination of ring stiffness |
| EN 1437:2002 | Plastics piping systems - Piping systems for underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading |
| EN 12256:1998 | Plastics piping systems - Thermoplastics fittings - Test method for mechanical strength or flexibility of fabricated fittings |
| EN ISO 472:2013 | Plastics - Vocabulary (ISO 472:2013) |
| EN 752-7 : 1998 | DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - MAINTENANCE AND OPERATIONS |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
| ISO 2505:2005 | Thermoplastics pipes — Longitudinal reversion — Test method and parameters |
| EN 1446 : 1996 | PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RING FLEXIBILITY |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.