BS 5410-1:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Code of practice for oil firing Installations up to 45 kW output capacity for space heating and hot water supply purposes
Hardcopy , PDF
23-08-2019
English
31-12-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Liquid fuels
5 Installation of oil fired appliances
6 Oil storage tanks and equipment
7 Accomodation for oil storage tanks
8 Installation of tanks
9 Oil system from storage tank to burner
10 Flues and chimneys
11 Design and installation of flues and chimneys
12 Room sealed balanced flue appliances
13 Special categories of flue system
14 Electrical installation and system controls
15 Commissioning
16 Maintenance
17 Conversion of appliances to oil firing
18 Biofuels
Annexes
Annex A (informative) - Types of appliances and burners
covered by this standard
Annex B (informative) - Example of a chimney designation
in accordance with BS EN 1443:2003
Bibliography
Provides recommendations and guidance on the design, installation, commissioning and maintenance of oil burning installations up to 45 kW output capacity for space heating and hot water supply purposes.
| Committee |
RHE/13
|
| DevelopmentNote |
Supersedes BS 5410-1(1997) & 14/30285453 DC. (01/2015)
|
| DocumentType |
Standard
|
| Pages |
66
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This part of BS5410 gives recommendations and guidance on the design, installation, commissioning and maintenance of oil burning installations up to 45kW output capacity for space heating and hot water supply purposes. It also gives recommendations and guidance on the selection and installation of oil tanks of capacity up to 3500L, when installed at buildings used primarily as dwellings. The standard is also applicable to oil fired cookers where these are connected to flues. This part of BS5410 is not applicable to oil fired systems for marine and transportable installations, or for flueless heaters. This part of BS5410 is applicable to installations burning liquid fuel conforming to BS2869:2010+A1 , including biofuels conforming to BSEN14214 , and blends thereof. This standard is intended for use by designers, specifiers, installers, and service and commissioning engineers. NOTE1 The types of appliances and burners covered by this part of BS5410 are described in AnnexA. NOTE2 Oil tank installations at buildings used primarily as dwelllings, with an oil storage capacity greater than 3500L are covered by BS5410‑2:2013 . NOTE3 Oil tank installations at buildings other than dwellings, with oil storage capacity up to 3500L, are covered by BS5410‑2:2013 , 10.7 .
| BS 476-4:1970 | Fire tests on building materials and structures Non-combustibility test for materials |
| BS 5410-2:2013 | Code of practice for oil firing Installations over 45 kW output capacity for space heating, hot water and steam supply services |
| BS EN 13341 : 2005 | STATIC THERMOPLASTIC TANKS FOR ABOVE GROUND STORAGE OF DOMESTIC HEATING OILS, KEROSENE AND DIESEL FUELS - BLOW MOULDED AND ROTATIONALLY MOULDED POLYETHYLENE TANKS AND ROTATIONALLY MOULDED TANKS MADE OF ANIONICALLY POLYMERIZED POLYAMIDE 6 - REQUIREMENTS AND TEST METHODS |
| BS EN 15287-1 : 2007 | CHIMNEYS - DESIGN, INSTALLATION AND COMMISSIONING OF CHIMNEYS - PART 1: CHIMNEYS FOR NON-ROOMSEALED HEATING APPLIANCES |
| BS EN 1806:2006 | Chimneys Clay/ceramic flue blocks for single wall chimneys Requirements and test methods |
| BS EN 13502:2002 | Chimneys. Requirements and test methods for clay/ceramic flue terminals |
| BS EN ISO 23553-1:2014 | Safety and control devices for oil burners and oil-burning appliances. Particular requirements Automatic and semi-automatic valves |
| BS EN 1857 : 2003 | CHIMNEYS - COMPONENTS - CONCRETE FLUE LINERS |
| BS EN 13063-1:2005 | Chimneys. System chimneys with clay/ceramic flue liners Requirements and test methods for sootfire resistance |
| BS 6150(2006) : 2006 | PAINTING OF BUILDINGS - CODE OF PRACTICE |
| BS EN 303-2:2017 | Heating boilers Heating boilers with forced draught burners. Special requirements for boilers with atomizing oil burners |
| BS EN 230:2005 | Automatic burner control systems for oil burners |
| BS EN 303-1:2017 | Heating boilers Heating boilers with forced draught burners. Terminology, general requirements, testing and marking |
| BS EN 13384-1 : 2002 | CHIMNEYS - THERMAL AND FLUID DYNAMIC CALCULATION METHODS - PART 1: CHIMNEYS SERVING ONE HEATING APPLIANCE |
| BS EN 13384-2 : 2003 | CHIMNEYS - THERMAL AND FLUID DYNAMIC CALCULATION METHODS - PART 2: CHIMNEYS SERVING MORE THAN ONE HEATING APPLIANCE |
| BS EN 12285-1:2003 | Workshop fabricated steel tanks Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable and non-flammable water polluting liquids |
| BS EN 13069:2005 | Chimneys. Clay/ceramic outer walls for system chimneys. Requirements and test methods |
| BS 41:1973 | Specification for cast iron spigot and socket flue or smoke pipes and fittings |
| BS EN 1057 : 2006 | COPPER AND COPPER ALLOYS - SEAMLESS, ROUND COPPER TUBES FOR WATER AND GAS IN SANITARY AND HEATING APPLICATIONS |
| BS EN 14241-1:2013 | Chimneys. Elastomeric seals and elastomeric sealants. Material requirements and test methods Seals in flue liners |
| BS 6999:1989 | Specification for vitreous-enamelled low-carbon-steel flue pipes, other components and accessories for solid-fuel-burning appliances with a rated output of 45 kW |
| BS 476-20:1987 | Fire tests on building materials and structures Method for determination of the fire resistance of elements of construction (general principles) |
| BS EN 267 : 2009 | AUTOMATIC FORCED DRAUGHT BURNERS FOR LIQUID FUELS |
| BS 476-21:1987 | Fire tests on building materials and structures Methods for determination of the fire resistance of loadbearing elements of construction |
| BS EN 1254-2:1998 | Copper and copper alloys. Plumbing fittings Fittings with compression ends for use with copper tubes |
| BS EN 1858 : 2008 | CHIMNEYS - COMPONENTS - CONCRETE FLUE BLOCKS |
| BS EN 15034:2006 | Heating boilers. Condensing heating boilers for fuel oil |
| BS EN 1457:1999 | Chimneys. Clay/ceramic flue liners. Requirements and test methods |
| BS EN 1443:2003 | Chimneys. General requirements |
| BS EN 50291:2001 | Electrical apparatus for the detection of carbon monoxide in domestic premises. Test methods and performance requirements |
| BS EN 1856-1:2009 | Chimneys. Requirements for metal chimneys System chimney products |
| BS EN 722-1:2004 | Leisure accommodation vehicles. Liquid fuel heating systems Caravans and caravan holiday homes |
| BS 9125:1988 | Specification for capability approval of manufacturers of passive radio interference suppression filter units of assessed quality generic data |
| BS EN 12446:2011 | Chimneys. Components. Concrete outer wall elements |
| BS EN 293:1992 | Specification for oil pressure atomizing nozzles. Minimum requirements. Testing |
| BS EN 12828 : 2012 | HEATING SYSTEMS IN BUILDINGS - DESIGN FOR WATER-BASED HEATING SYSTEMS |
| BS EN 14125:2013 | Thermoplastic and flexible metal pipework for underground installation at petrol filling stations |
| BS EN 13063-2:2005 | Chimneys. System chimneys with clay/ceramic flue liners Requirements and test methods under wet conditions |
| BS 5422:2001 | Method for specifying thermal insulating materials for pipes, tanks, vessels, ductwork and equipment operating within the temperature range -40°C to +700°C |
| BS 476-22:1987 | Fire tests on building materials and structures Method for determination of the fire resistance of non-loadbearing elements of construction |
| BS EN 14471 : 2013 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| BS EN 14214:2012 | LIQUID PETROLEUM PRODUCTS - FATTY ACID METHYL ESTERS (FAME) FOR USE IN DIESEL ENGINES AND HEATING APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| BS 799-8:1988 | Oil burning equipment Specification for connecting dimensions between atomizing oil burners and heat generators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.