ASTM D 5064 : 2016 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Conducting a Patch Test to Assess Coating Compatibility
Hardcopy , PDF
02-07-2021
English
30-12-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 01
|
| DocumentType |
Standard Practice
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice covers the procedures for assessing coating compatibility when maintenance of an in-place coating system is being contemplated. It does not address procedures for assessing the integrity of the existing coating to determine if it can be repainted, nor does it establish the compatibility of the maintenance coating system with the substrate or corrosion products. The practice is intended for use in the field. SSPC-TU 3 discusses the risks associated with the maintenance painting practice known as overcoating.
Note 1:Pass-Fail Criteria (for example, adhesion requirements) are not established by this practice. These should be established by the user or specifier with input from the coating manufacturer.
1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 6237 : 2009 : R2015 | Standard Guide for Painting Inspectors (Concrete and Masonry Substrates) |
| ASTM E 1796 : 2003 : R2016 | Standard Guide for Selection and Use of Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| ASTM D 3276 : 2015 : EDT 1 | Standard Guide for Painting Inspectors (Metal Substrates) |
| ASTM D 6577 : 2015 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM E 1796 : 2020 | Standard Guide for Selection and Use of Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| ASTM D 6577 : 2015 : R2019 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM D 6237 : 2019 | Standard Guide for Painting Inspectors (Concrete and Masonry Substrates) |
| ASTM D 7234 : 2005 | Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
| ASTM D 6132 : 1997 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Over Concrete Using an Ultrasonic Gage |
| ASTM D 3359 : 1997 | Standard Test Methods for Measuring Adhesion by Tape Test |
| ASTM D 7091 : 2020 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM D 4414 : 1995 | Standard Practice for Measurement of Wet Film Thickness by Notch Gages |
| ASTM D 4541 : 2017 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 6132 : 2013 : R2017 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage |
| ASTM D 4138 : 1994 : R1999 | Standard Test Methods for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive Means |
| ASTM D 6677 : 2001 | Standard Test Method for Evaluating Adhesion by Knife |
| ASTM D 7091 : 2021 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM D 7091 : 2005 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM D 4138 : 2007 : REV A : R2017 | Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means |
| ASTM D 4541 : 1995 : EDT 1 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 4414 : 1995 : R2001 | Standard Practice for Measurement of Wet Film Thickness by Notch Gages |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.