I.S. EN 61191-2:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PRINTED BOARD ASSEMBLIES - PART 2: SECTIONAL SPECIFICATION - REQUIREMENTS FOR SURFACE MOUNT SOLDERED ASSEMBLIES
English
01-01-2017
11-20-2019
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
National Foreword
FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
5 Surface mounting of components
6 Acceptance requirements
7 Rework and repair
Annex A (normative) - Placement requirements
for surface mounted devices
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Provides the requirements for surface mount solder connections.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
48
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NF EN 61191-2 : 2014 | Identical |
| NBN EN 61191-2 : 2013 | Identical |
| EN 61191-2:2017 | Identical |
| DIN EN 61191-2:2016-01 (Draft) | Identical |
| BS EN 61191-2:2017 | Equivalent |
| EN 61191-2:2017 | Equivalent |
| IEC 61193-3:2013 | Quality assessment systems - Part 3: Selection and use of sampling plans for printed board and laminate end-product and in-process auditing |
| IEC 61193-1:2001 | Quality assessment systems - Part 1: Registration and analysis of defects on printed board assemblies |
| IEC 61188-5-3:2007 | Printed boards and printed board assemblies - Design and use - Part 5-3: Attachment (land/joint) considerations - Components with gull-wing leads on two sides |
| IEC 61188-5-2:2003 | Printed boards and printed board assemblies - Design and use - Part 5-2: Attachment (land/joint) considerations - Discrete components |
| IEC 60068-2-58:2015+AMD1:2017 CSV | Environmental testing - Part 2-58: Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD) |
| IEC 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
| IEC 61190-1-2:2014 | Attachment materials for electronic assembly - Part 1-2: Requirements for soldering pastes for high-quality interconnects in electronics assembly |
| IEC 62326-1:2002 | Printed boards - Part 1: Generic specification |
| IEC 62326-4:1996 | Printed boards - Part 4: Rigid multilayer printed boards with interlayer connections - Sectional specification |
| IEC 61188-7:2017 | Printed boards and printed board assemblies - Design and use - Part 7: Electronic component zero orientation for CAD library construction |
| IEC 61191-1:2013 | Printed board assemblies - Part 1: Generic specification - Requirements for soldered electrical and electronic assemblies using surface mount and related assembly technologies |
| IEC 61188-5-6:2003 | Printed boards and printed board assemblies - Design and use - Part 5-6: Attachment (land/joint) considerations - Chip carriers with J-leads on four sides |
| IEC 61188-5-1:2002 | Printed boards and printed board assemblies - Design and use - Part 5-1: Attachment (land/joint) considerations - Generic requirements |
| IEC 60194:2015 | Printed board design, manufacture and assembly - Terms and definitions |
| IEC 61188-5-5:2007 | Printed boards and printed board assemblies - Design and use - Part 5-5: Attachment (land/joint) considerations - Components with gull-wing leads on four sides |
| ISO 9001:2015 | Quality management systems — Requirements |
| IEC 62326-4-1:1996 | Printed boards - Part 4: Rigid multilayer printed boards with interlayer connections - Sectional specification - Section 1: Capability detail specification - Performance levels A, B and C |
| EN 61191-1:2013 | Printed board assemblies - Part 1: Generic specification - Requirements for soldered electrical and electronic assemblies using surface mount and related assembly technologies |
| IEC 61188-5-4:2007 | Printed boards and printed board assemblies - Design and use - Part 5-4: Attachment (land/joint) considerations - Components with J leads on two sides |
| IEC 61189-2:2006 | Test methods for electrical materials, printed boards and other interconnection structures and assemblies - Part 2: Test methods for materials for interconnection structures |
| EN 60194:2006 | Printed board design, manufacture and assembly - Terms and definitions |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.