UNI EN 15061 : 2009

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
  5.1 General design requirements
      5.1.1 Introduction
      5.1.2 Structural assembly
      5.1.3 Safety layout
      5.1.4 Access to the line
      5.1.5 Guards
      5.1.6 Guard-rail
      5.1.7 Safety signs and warning devices
      5.1.8 Safety-related control systems
      5.1.9 Personal protective equipment (PPE)
      5.1.10 Electrical equipment
      5.1.11 Hydraulic, pneumatic, cooling and lubrication
             systems
      5.1.12 Fluid systems carrying or containing fluids
      5.1.13 Material to be discharged to drains
      5.1.14 Ergonomic principles
      5.1.15 Surface temperatures and heat radiation
      5.1.16 Fire protection
      5.1.17 Vibrations
      5.1.18 Maintenance on equipment containing dangerous
             substances
      5.1.19 Linked equipment
  5.2 List of significant hazards, hazardous situations,
      safety requirements and/or measures for terminal
      equipment
      5.2.1 General
      5.2.2 Hydraulic and pneumatic equipment
      5.2.3 Bridges, crossovers, guides
      5.2.4 Pulpits
      5.2.5 Coil transport and handling equipment
      5.2.6 Uncoiling equipment
      5.2.7 Shears and scrap/samples handling equipment
      5.2.8 Strip guiding and conveying equipment
      5.2.9 Strip accumulators
      5.2.10 Side trimming machines
      5.2.11 Strip inspection stands
      5.2.12 Coiling equipment
      5.2.13 Strip connecting system
      5.2.14 Oiling system
      5.2.15 Measuring devices and display units
      5.2.16 Marking devices for strip
  5.3 List of significant hazards, hazardous situations,
      safety requirements and/or measures for processing
      equipment
      5.3.1 General
      5.3.2 Hydraulic and pneumatic equipment
      5.3.3 Bridges, crossovers, guides
      5.3.4 Pulpits
      5.3.5 Pickling
      5.3.6 Pre-treatment
      5.3.7 Hot dipping
      5.3.8 Electro plating
      5.3.9 Tension leveller, scale breaker
      5.3.10 Organic coating by roll coater
      5.3.11 Chemical post-treatment section (Activation,
             Phosphatizing, Chromatizing, Roll coating)
  5.4 Special safety requirements or measures
      5.4.1 General
      5.4.2 Hold-to-run control device
      5.4.3 Mechanical restraint devices
      5.4.4 Access to the strip for inspection
  5.5 Noise reduction as a safety requirement
      5.5.1 Noise reduction at source by design
      5.5.2 Noise reduction by protective measures
      5.5.3 Noise reduction by information
      5.5.4 Noise sources and examples of noise reduction
             measures
6 Verification of the safety requirements and/or measures
7 Information for use
  7.1 General
  7.2 Safety signs and warning devices
  7.3 Minimum marking
  7.4 Instruction handbook
      7.4.1 General
      7.4.2 Identifying information
      7.4.3 Detailed information/instructions
      7.4.4 Operation
  7.5 Maintenance manual
Annex A (normative) - Safety requirements and/or measures
        for electrical equipment
Annex B (normative) - Noise test code
Annex C (informative) - Example for manufacturer's safety
        instructions for maintenance at strip processing
        lines
Annex D (informative) - Exemplary solutions
Annex ZA (informative) - Relationship between this
         European Standard and the Essential Requirements of
         EU Directive 98/37/EC
Annex ZB (informative) - Relationship between this
         European Standard and the Essential Requirements of
         EU Directive 2006/42/EC
Bibliography

Describes the health and safety requirements of strip processing lines.