I.S. EN ISO 11295:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
CLASSIFICATION AND INFORMATION ON DESIGN AND APPLICATIONS OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION AND REPLACEMENT (ISO 11295:2017)
Hardcopy , PDF
10-03-2022
English
01-01-2017
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviated terms
5 Classification of renovation and replacement techniques
6 Classification of renovation techniques
7 Classification of trenchless replacement techniques
8 Information on design
9 Aspects affecting installation
Bibliography
Defines families of techniques for the renovation and trenchless replacement (on or off the line of an existing pipeline) of non-pressure and pressure pipelines through the use of plastics pipes, including plastics composites formed in situ into pipes, fittings and ancillary components.
| DevelopmentNote |
Supersedes I.S. EN 13689. (03/2010)
|
| DocumentType |
Standard
|
| Pages |
68
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 11295:2017 | Identical |
| EN ISO 11295:2017 | Identical |
| ISO 25780:2011 | Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Pipes with flexible joints intended to be installed using jacking techniques |
| EN 14636-1:2009 | Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints |
| ISO 10467:2004 | Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin |
| ISO 11296-1:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General |
| ISO 10639:2017 | Plastics piping systems for pressure and non-pressure water supply Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin |
| ISO 11296-3:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 3: Lining with close-fit pipes |
| ISO 11299-1:2011 | Plastics piping systems for renovation of underground gas supply networks Part 1: General |
| ISO 11296-7:2011 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 7: Lining with spirally-wound pipes |
| ISO 24511:2007 | Activities relating to drinking water and wastewater services — Guidelines for the management of wastewater utilities and for the assessment of wastewater services |
| EN 12889:2000 | Trenchless construction and testing of drains and sewers |
| ISO 18672-1:2009 | Plastics piping systems for non-pressure drainage and sewerage — Polyester resin concrete (PRC) — Part 1: Pipes and fittings with flexible joints |
| ISO 24512:2007 | Activities relating to drinking water and wastewater services — Guidelines for the management of drinking water utilities and for the assessment of drinking water services |
| ISO 11299-3:2011 | Plastics piping systems for renovation of underground gas supply networks Part 3: Lining with close-fit pipes |
| ISO 11298-3:2010 | Plastics piping systems for renovation of underground water supply networks Part 3: Lining with close-fit pipes |
| ISO 11296-4:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 4: Lining with cured-in-place pipes |
| ISO 11298-1:2010 | Plastics piping systems for renovation of underground water supply networks Part 1: General |
| ISO 16611:2017 | Plastics piping systems for drainage and sewerage without pressure — Non-circular pipes and joints made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resins (UP) — Dimensions, requirements and tests |
| ISO 24510:2007 | Activities relating to drinking water and wastewater services — Guidelines for the assessment and for the improvement of the service to users |
| ISO 11297-1:2013 | Plastics piping systems for renovation of underground drainage and sewerage networks under pressure Part 1: General |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| EN 16506:2014 | Systems for renovation of drains and sewers - Lining with a rigidly anchored plastics inner layer (RAPL) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.