EN 754-7:2016
Current
Current
The latest, up-to-date edition.
Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 7: Seamless tubes, tolerances on dimensions and form
Published date
08-06-2016
Publisher
Sorry this product is not available in your region.
European foreword
1 Scope
2 Normative references
3 Tolerances on dimensions
4 Tolerances on form
Annex A (informative) - Wall thickness variation
(eccentricity)
Bibliography
This European Standard specifies the tolerances on dimensions and form for aluminium and aluminium alloys cold drawn seamless tubes with an outside diameter (OD) from 3 mm to 350 mm (round tube, see Figure 1) or with a cross section contained within a circumscribing circle (CD) from 8 mm to 300 mm (other than round tube, see Figure 2) supplied in straight lengths.This European Standard only applies to tube produced by the seamless die/mandrel method of extrusion (and then cold drawn to the final dimensions required).The temper designations used in this part are according to EN 515.This document applies to cold drawn, seamless tube for general engineering applications.This document does not apply to:-cold drawn tube produced by the porthole/bridge method (EN 754-8),-tubes delivered in coils (EN 13958),-coiled tubes cut to length (EN 13958).(...)
| Committee |
CEN/TC 132
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| UNI EN 754-7:2016 | Identical |
| NEN EN 754-7 : 2016 | Identical |
| SN EN 754-7 : 2016 | Identical |
| NS EN 754-7 : 2ED 2008 | Identical |
| PN EN 754-7 : 2016 | Identical |
| UNI EN 754-7 : 2008 | Identical |
| NF EN 754-7 : 2016 | Identical |
| NBN EN 754-7 : 2016 | Identical |
| NEN EN 754-7 : 2016 | Similar to |
| I.S. EN 754-7:2016 | Identical |
| SN EN 754-4 : 2008 | Identical |
| SN EN 754-5 : 2008 | Identical |
| DIN EN 754-7:2016-10 | Identical |
| BS EN 754-7:2016 | Identical |
| UNE-EN 754-7:2016 | Identical |
| UNE-EN 13195:2014 | Aluminium and aluminium alloys - Specifications for wrought and cast products for marine applications (shipbuilding, marine and offshore) |
| 06/30136505 DC : 0 | EN 754-1 - ALUMINIUM AND ALUMINIUM ALLOYS - COLD DRAWN ROD/BAR AND TUBE - PART 1: TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY |
| UNI EN 1090-3 : 2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| 14/30301152 DC : 0 | BS EN 12392 - ALUMINIUM AND ALUMINIUM ALLOYS - WROUGHT PRODUCTS AND CAST PRODUCTS - SPECIAL REQUIREMENTS FOR PRODUCTS INTENDED FOR THE PRODUCTION OF PRESSURE EQUIPMENT |
| DIN EN 13195:2013-12 | ALUMINIUM AND ALUMINIUM ALLOYS - SPECIFICATIONS FOR WROUGHT AND CAST PRODUCTS FOR MARINE APPLICATIONS (SHIPBUILDING, MARINE AND OFFSHORE) |
| PREN 12392 : DRAFT 2014 | ALUMINIUM AND ALUMINIUM ALLOYS - WROUGHT PRODUCTS AND CAST PRODUCTS - SPECIAL REQUIREMENTS FOR PRODUCTS INTENDED FOR THE PRODUCTION OF PRESSURE EQUIPMENT |
| 98/105109 DC : DRAFT JUNE 1998 | PREN 1317-5 - ROAD RESTRAINT SYSTEMS - PART 5: DURABILITY AND EVALUATION OF CONFORMITY |
| I.S. EN 1090-3:2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| ONORM EN 1090-3 : 2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| DIN EN 754-8:2016-10 | ALUMINIUM AND ALUMINIUM ALLOYS - COLD DRAWN ROD/BAR AND TUBE - PART 8: PORTHOLE TUBES, TOLERANCES ON DIMENSIONS AND FORM |
| BS EN 13958:2008 | Aluminium and aluminium alloys. Cold drawn, round, coiled tube for general applications. Specification |
| BS EN 754-1:2016 | Aluminium and aluminium alloys. Cold drawn rod/bar and tube Technical conditions for inspection and delivery |
| DIN EN 13958:2009-01 | ALUMINIUM AND ALUMINIUM ALLOYS - COLD DRAWN, ROUND, COILED TUBE FOR GENERAL APPLICATIONS - SPECIFICATION |
| EN 13195:2013 | Aluminium and aluminium alloys - Specifications for wrought and cast products for marine applications (shipbuilding, marine and offshore) |
| EN 13958:2008 | Aluminium and aluminium alloys - Cold drawn, round, coiled tube for general applications - Specification |
| EN 13195-1 : 2002 | ALUMINIUM AND ALUMINIUM ALLOYS - WROUGHT AND CAST PRODUCTS FOR MARINE APPLICATIONS (SHIPBUILDING, MARINE AND OFFSHORE) - PART 1: SPECIFICATIONS |
| EN 12392:2016 | Aluminium and aluminium alloys - Wrought products and cast products - Special requirements for products intended for the production of pressure equipment |
| DIN EN 13195-1:2002-11 | ALUMINIUM AND ALUMINIUM ALLOYS - WROUGHT AND CAST PRODUCTS FOR MARINE APPLICATIONS (SHIPBUILDING, MARINE AND OFFSHORE) - PART 1: SPECIFICATIONS |
| 09/30202316 DC : 0 | BS EN 12514-4 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 4: SAFETY REQUIREMENTS AND TESTS - PIPINGS AND PARTS WITHIN PIPELINES |
| PREN 1090-3 : DRAFT 2017 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| UNI EN 13195 : 2013 | ALUMINIUM AND ALUMINIUM ALLOYS - SPECIFICATIONS FOR WROUGHT AND CAST PRODUCTS FOR MARINE APPLICATIONS (SHIPBUILDING, MARINE AND OFFSHORE) |
| I.S. EN 754-1:2016 | ALUMINIUM AND ALUMINIUM ALLOYS - COLD DRAWN ROD/BAR AND TUBE - PART 1: TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY |
| BS EN 1999-1-1 : 2007 | EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES |
| I.S. EN 1999-1-1:2007 | EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES (INCLUDING IRISH NATIONAL ANNEX) |
| ONORM EN 754-1 : 2008 | ALUMINIUM AND ALUMINIUM ALLOYS - COLD DRAWN ROD/BAR AND TUBE - PART 1: TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY |
| I.S. EN 570:2007 | ALUMINIUM AND ALUMINIUM ALLOYS - IMPACT EXTRUSION SLUGS OBTAINED FROM WROUGHT PRODUCTS - SPECIFICATIONS |
| I.S. EN 754-8:2016 | ALUMINIUM AND ALUMINIUM ALLOYS - COLD DRAWN ROD/BAR AND TUBE - PART 8: PORTHOLE TUBES, TOLERANCES ON DIMENSIONS AND FORM |
| I.S. EN 13195-1:2002 | ALUMINIUM AND ALUMINIUM ALLOYS - WROUGHT AND CAST PRODU- PART 1: SPECIFICATIONS (SHIPBUILDING, MARINE AND OFFSHORE) |
| I.S. EN 12392:2016 | ALUMINIUM AND ALUMINIUM ALLOYS - WROUGHT PRODUCTS AND CAST PRODUCTS - SPECIAL REQUIREMENTS FOR PRODUCTS INTENDED FOR THE PRODUCTION OF PRESSURE EQUIPMENT |
| DIN EN 1999-1-1:2014-03 | Eurocode 9: Design of aluminium structures - Part 1-1: General structural rules |
| 05/30133060 DC : 0 | EN 1090-3 - EXECUTION OF STEEL AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL RULES FOR EXECUTION OF ALUMINIUM STRUCTURES |
| PREN 754-1 : DRAFT 2015 | ALUMINIUM AND ALUMINIUM ALLOYS - COLD DRAWN ROD/BAR AND TUBE - PART 1: TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY |
| 15/30324460 DC : 0 | BS EN 754-1 - ALUMINIUM AND ALUMINIUM ALLOYS - COLD DRAWN ROD/BAR AND TUBE - PART 1: TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY |
| EN 1090-3:2008 | Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures |
| DIN EN 12392:2016-08 | Aluminium and aluminium alloys - Wrought products and cast products - Special requirements for products intended for the production of pressure equipment |
| DIN EN 573-5:2007-11 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 5: Codification of standardized wrought products |
| DIN EN 754-1:2016-10 | ALUMINIUM AND ALUMINIUM ALLOYS - COLD DRAWN ROD/BAR AND TUBE - PART 1: TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY |
| BS EN 13195-1:2002 | Aluminium and aluminium alloys. Wrought and cast products for marine applications (shipbuilding, marine and offshore) Specifications |
| UNE-EN 754-8:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 8: Porthole tubes, tolerances on dimensions and form |
| BS EN 754-8:2016 | Aluminium and aluminium alloys. Cold drawn rod/bar and tube Porthole tubes, tolerances on dimensions and form |
| UNI EN 13958 : 2009 | ALUMINIUM AND ALUMINIUM ALLOYS - COLD DRAWN, ROUND, COILED TUBE FOR GENERAL APPLICATIONS - SPECIFICATION |
| UNI EN 754-8 : 2008 | ALUMINIUM AND ALUMINIUM ALLOYS - COLD DRAWN ROD/BAR AND TUBE - PART 8: PORTHOLE TUBES, TOLERANCES ON DIMENSIONS AND FORM |
| UNI EN 1999-1-1 : 2014 | EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES |
| BS EN 1090-3:2008 | Execution of steel structures and aluminium structures Technical requirements for aluminium structures |
| 17/30348949 DC : 0 | BS EN 1090-3 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| EN 754-1:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 1: Technical conditions for inspection and delivery |
| I.S. EN 13195:2013 | ALUMINIUM AND ALUMINIUM ALLOYS - SPECIFICATIONS FOR WROUGHT AND CAST PRODUCTS FOR MARINE APPLICATIONS (SHIPBUILDING, MARINE AND OFFSHORE) |
| BS EN 12392:2016 | Aluminium and aluminium alloys. Wrought products and cast products. Special requirements for products intended for the production of pressure equipment |
| UNE-EN 754-1:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 1: Technical conditions for inspection and delivery |
| UNE-EN 13958:2010 | Aluminium and aluminium alloys - Cold drawn, round, coiled tube for general applications - Specification |
| DIN EN 15088:2016-09 (Draft) | Aluminium and aluminium alloys - Structural products for construction works - Technical conditions for inspection and delivery; German and English version prEN 15088:2016 |
| BS EN 15088:2005 | Aluminium and aluminium alloys. Structural products for construction works. Technical conditions for inspection and delivery |
| EN 15088:2005 | Aluminium and aluminium alloys - Structural products for construction works - Technical conditions for inspection and delivery |
| EN 570:2007 | Aluminium and aluminium alloys - Impact extrusion slugs obtained from wrought products - Specification |
| EN 573-5:2007 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 5: Codification of standardized wrought products |
| EN 754-8:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 8: Porthole tubes, tolerances on dimensions and form |
| BS EN 13195:2013 | Aluminium and aluminium alloys. Specifications for wrought and cast products for marine applications (shipbuilding, marine and offshore) |
| 04/30125694 DC : DRAFT NOV 2004 | EN 15088 - ALUMINIUM AND ALUMINIUM ALLOYS - STRUCTURAL PRODUCTS FOR CONSTRUCTION WORKS - TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY |
| DIN EN 1090-3:2008-09 | EXECUTION OF STEEL AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL RULES FOR EXECUTION OF ALUMINIUM STRUCTURES |
| UNE-EN 1090-3:2011 | Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures |
| BS EN 573-5:2007 | Aluminium and aluminium alloys. Chemical composition and form of wrought products Codification of standardized wrought products |
| BS EN 570:2007 | Aluminium and aluminium alloys. Impact extrusion slugs obtained from wrought products. Specification |
| DIN EN 15088:2006-03 | Aluminium and aluminium alloys - Structural products for construction works - Technical conditions for inspection and delivery; German version EN 15088:2005 |
| DIN EN 570:2007-04 | Aluminium and aluminium alloys - Impact extrusion slugs obtained from wrought products - Specification |
| EN 754-1:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 1: Technical conditions for inspection and delivery |
| EN 13958:2008 | Aluminium and aluminium alloys - Cold drawn, round, coiled tube for general applications - Specification |
| EN 515:2017 | Aluminium and aluminium alloys - Wrought products - Temper designations |
| EN 754-8:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 8: Porthole tubes, tolerances on dimensions and form |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.