EN 14673:2006+A1:2010
Current
Current
The latest, up-to-date edition.
Safety of machinery - Safety requirements for hydraulically powered open die hot forging presses for the forging of steel and non-ferrous metals
Published date
07-04-2010
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
6 Verification of the safety requirements and/or measures
7 Information for use
Annex A (normative) Safety requirements for hydraulic, pressure
water and lubrication systems
Annex B (normative) Safety requirements and/or measures for
electrical equipment and control systems for
hydraulically powered open die hot forging
presses
Annex C (normative) Noise test code
Annex D (informative) De-commissioning
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements
of EU Directive 2006/42/EC
Bibliography
This European Standard applies to:-hydraulically powered open die forging presses for hot working;-handling and cooling equipment connected with the control system of the forging line, e. g., manipulators, rotating type handling devices, die shifting devices, table devices and tool changing devices;-handling equipment designed specifically to be used within the forging line, e. g., material manipulation devices, turnover or handling devices attached to fork lift trucks or cranes etc.It specifies the health and safety requirements at all stages in the life of the equipment, its design, ordering, construction, use and disposal.This European Standard specifies requirements to be met by the manufacturer to ensure the health and safety of persons during construction, transport, commissioning, operation, maintenance and de-commissioning, as well as in the event of foreseeable faults as malfunctions which may occur in the equipment.This European Standard deals with all significant hazards, hazardous situations and events relevant to hydraulically powered hot forging presses when they are used as intended and under conditions foreseeable by the manufacturer (see Clause 4).This European Standard does not cover:-hydraulically controlled closed die forging presses for hot working;-mechanically powered hot forging presses;-mobile manipulators as defined in 3.4.2;-standard transport and lifting equipment modified for use with material manipulation devices, turnover and handling devices such as for fork lift trucks and cranes.This European Standard is not applicable to machinery which was manufactured before the date of publication of this standard by CEN.
| Committee |
CEN/TC 322
|
| DevelopmentNote |
2006 Edition Re-issued in April 2010 & incorporates AMD 1 2010. (05/2010) Supersedes UNE EN 14673. (03/2011)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| PN EN 14673 : 2008 + A1 2012 | Identical |
| DIN EN 14673:2010-10 | Identical |
| SN EN 14673 : 2007 + A1 2010 | Identical |
| UNE-EN 14673:2006+A1:2010 | Identical |
| BS EN 14673 : 2006 | Identical |
| UNI EN 14673 : 2010 | Identical |
| NS EN 14673 : 2006 + A1 2010 | Identical |
| I.S. EN 14673:2006 | Identical |
| NBN EN 14673 : 2007 + A1 2010 | Identical |
| NEN EN 14673 : 2006 + A1 2010 | Identical |
| NF EN 14673 : 2007 + A1 2010 | Identical |
| BS EN 14673:2006+A1:2010 | Identical |
| PNE-EN 14673:2006/FprA1 | Identical |
| UNE-EN 14673:2007 | Identical |
| EN 12096:1997 | Mechanical vibration - Declaration and verification of vibration emission values |
| ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| ISO 11200:2014 | Acoustics Noise emitted by machinery and equipment Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions |
| EN 13480-2:2017 | Metallic industrial piping - Part 2: Materials |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| ISO 14122-3:2016 | Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails |
| EN 14253:2003+A1:2007 | Mechanical vibration - Measurement and calculation of occupational exposure to whole-body vibration with reference to health - Practical guidance |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| EN 1591-1:2013 | Flanges and their joints - Design rules for gasketed circular flange connections - Part 1: Calculation |
| ISO 14122-1:2016 | Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access |
| ISO 11546-2:1995 | Acoustics Determination of sound insulation performances of enclosures Part 2: Measurements in situ (for acceptance and verification purposes) |
| EN 60825-1:2014/AC:2017-06 | SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014) |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| IEC 61310-2:2007 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| EN 981:1996+A1:2008 | Safety of machinery - System of auditory and visual danger and information signals |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| EN 13480-4:2017 | Metallic industrial piping - Part 4: Fabrication and installation |
| IEC 60073:2002 | Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators |
| EN 61310-2:2008 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| EN 60073:2002 | Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
| EN 614-2:2000+A1:2008 | Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of machinery and work tasks |
| EN ISO 14121-1:2007 | Safety of machinery - Risk assessment - Part 1: Principles (ISO 14121-1:2007) |
| EN 1837:1999+A1:2009 | Safety of machinery - Integral lighting of machines |
| EN 999:1998+A1:2008 | Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body |
| EN 13861:2011 | Safety of machinery - Guidance for the application of ergonomics standards in the design of machinery |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| EN 1299:1997+A1:2008 | Mechanical vibration and shock - Vibration isolation of machines - Information for the application of source isolation |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| ISO 3747:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering/survey methods for use in situ in a reverberant environment |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
| ISO 3740:2000 | Acoustics Determination of sound power levels of noise sources Guidelines for the use of basic standards |
| EN 13480-1:2017 | Metallic industrial piping - Part 1: General |
| ISO 9614-2:1996 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning |
| EN ISO 7731:2008 | Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003) |
| EN ISO 11820:1996 | Acoustics - Measurements on silencers in situ (ISO 11820:1996) |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| ISO 14121-1:2007 | Safety of machinery Risk assessment Part 1: Principles |
| ISO 7731:2003 | Ergonomics Danger signals for public and work areas Auditory danger signals |
| EN ISO 11200:2014 | Acoustics - Noise emitted by machinery and equipment - Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions (ISO 11200:2014) |
| ISO 3795:1989 | Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials |
| EN ISO 13732-1:2008 | Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006) |
| ISO 11820:1996 | Acoustics — Measurements on silencers in situ |
| EN 13480-3:2017 | Metallic industrial piping - Part 3: Design and calculation |
| EN ISO 11546-2:2009 | Acoustics - Determination of sound insulation performances of enclosures - Part 2: Measurements in situ (for acceptance and verification purposes) (ISO 11546-2:1995) |
| EN 60447:2004 | Basic and safety principles for man-machine interface, marking and identification - Actuating principles |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| EN ISO 14122-3:2016 | Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016) |
| EN ISO 3747:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering/survey methods for use in situ in a reverberant environment (ISO 3747:2010) |
| EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
| EN 61496-1:2013/AC:2015 | SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 1: GENERAL REQUIREMENTS AND TESTS (IEC 61496-1:2012) |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN 842:1996+A1:2008 | Safety of machinery - Visual danger signals - General requirements, design and testing |
| EN ISO 14122-2:2016 | Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016) |
| EN ISO 3740:2000 | Acoustics - Determination of sound power levels of noise sources - Guidelines for the use of basic standards (ISO 3740:2000) |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| IEC 61496-1:2012 | Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests |
| EN ISO 9614-2:1996 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 2: Measurement by scanning (ISO 9614-2:1996) |
| ISO 11203:1995 | Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level |
| EN ISO 6682:2008 | Earth-moving machinery - Zones of comfort and reach for controls (ISO 6682:1986, including Amd 1:1989) |
| ISO 3864-1:2011 | Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings |
| EN 12198-3:2002+A1:2008 | Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 3: Reduction of radiation by attenuation or screening |
| EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
| ISO 11064-1:2000 | Ergonomic design of control centres Part 1: Principles for the design of control centres |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| ISO 11546-1:1995 | Acoustics Determination of sound insulation performances of enclosures Part 1: Measurements under laboratory conditions (for declaration purposes) |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 50171 : 2001 COR 2001 | CENTRAL POWER SUPPLY SYSTEMS |
| EN 626-1:1994+A1:2008 | Safety of machinery - Reduction of risks to health from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers |
| EN ISO 11064-1:2000 | Ergonomic design of control centres - Part 1: Principles for the design of control centres (ISO 11064-1:2000) |
| EN ISO 11691:2009 | Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method (ISO 11691:1995) |
| EN ISO 11821:1997 | Acoustics - Measurement of the in situ sound attenuation of a removable screen (ISO 11821:1997) |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| EN ISO 11546-1:2009 | Acoustics - Determination of sound insulation performances of enclosures - Part 1: Measurements under laboratory conditions (for declaration purposes) (ISO 11546-1:1995) |
| 1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
| ISO 14122-2:2016 | Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
| EN 13480-5:2017 | Metallic industrial piping - Part 5: Inspection and testing |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| EN ISO 14122-1:2016 | Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN ISO 9614-1:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993) |
| EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
| EN ISO 11203:2009 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level (ISO 11203:1995) |
| ISO 11691:1995 | Acoustics Measurement of insertion loss of ducted silencers without flow Laboratory survey method |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.