DIN EN 10025-3:2011-04 (Draft)
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 3: TECHNICAL DELIVERY CONDITIONS FOR NORMALIZED/NORMALIZED ROLLED WELDABLE FINE GRAIN STRUCTURAL STEELS
Hardcopy , PDF
07-10-2019
German
01-01-2011
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Vorwort
1 Anwendungsbereich
2 Normative Verweisungen
2.1 Allgemeine Normen
2.2 Normen für Masse und Grenzabmasse
2.3 Prüfnormen
3 Begriffe
4 Einteilung und Bezeichnung
4.1 Einteilung
4.1.1 Hauptgüteklassen
4.1.2 Sorten und Gütegruppen
4.2 Bezeichnung
5 Bestellangaben
5.1 Verbindliche Angaben
5.2 Optionen
6 Herstellverfahren
6.1 Stahlherstellverfahren
6.2 Korngrösse
6.3 Lieferzustand
7 Anforderungen
7.1 Allgemeines
7.2 Chemische Zusammensetzung
7.3 Mechanische Eigenschaften
7.3.1 Allgemeines
7.3.2 Kerbschlageigenschaften
7.3.3 Verbesserte Verformungseigenschaften senkrecht
zur Erzeugnisoberfläche
7.4 Technologische Eigenschaften
7.4.1 Schweisseignung
7.4.2 Umformbarkeit
7.4.3 Eignung zum Schmelztauchverzinken
7.5 Oberflächenbeschaffenheit
7.5.1 Band
7.5.2 Blech und Breitflachstahl
7.5.3 Profile
7.5.4 Stäbe und Walzdraht
7.6 Innere Beschaffenheit
7.7 Masse, Grenzabmasse, Formtoleranzen, Masse
8 Prüfung
8.1 Allgemeines
8.2 Art der Prüfung und Prüfbescheinigung
8.3 Prüfumfang
8.3.1 Probenahme
8.3.2 Prüfeinheiten
8.3.3 Nachweis der chemischen Zusammensetzung
8.4 Bei spezifischen Prüfungen durchzuführende Prüfungen
9 Vorbereitung von Probenabschnitten und Proben
9.1 Entnahme und Vorbereitung von Probenabschnitten
für die chemische Analyse
9.2 Lage und Richtung von Probenabschnitten und
Proben für mechanische Prüfungen
9.2.1 Allgemeines
9.2.2 Vorbereitung von Probenabschnitten
9.2.3 Vorbereitung von Proben
9.2.4 Kerbschlagproben
9.3 Identifizierung von Probenabschnitten und Proben
10 Prüfverfahren
10.1 Chemische Analyse
10.2 Mechanische Prüfungen
10.3 Ultraschallprüfung
10.4 Wiederholungsprüfungen
11 Kennzeichnung, Beschilderung, Verpackung
12 Beanstandungen
13 Optionen
Anhang A (informativ) Liste der früheren Bezeichnungen
vergleichbarer Stähle
Anhang B (informativ) Liste der den zitierten EURONORMEN
entsprechenden nationalen Normen
Literaturhinweise
This standard is included in DIN Handbook 402 and DIN DVS Handbook 191. Specifies requirements for flat and long products of hot rolled weldable fine grain structural steels in the normalized/normalized rolled delivery condition in the grades and qualities.
| DevelopmentNote |
Supersedes DIN EN 10113-2 (02/2005) DRAFT 2011 issued in April 2011. (05/2011)
|
| DocumentType |
Draft
|
| Pages |
24
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| NBN EN 10025-3 : 2005 | Identical |
| UNI EN 10025-3 : 2005 | Identical |
| NS EN 10025-3 : 1ED 2005 | Identical |
| NEN EN 10025-3 : 2004 | Identical |
| EN 10025-3:2004 | Identical |
| NF EN 10025-3 : 2005 | Identical |
| BS EN 10025-3:2004 | Identical |
| SN EN 10025-3 : 2005 | Identical |
| I.S. EN 10025-3:2004 | Identical |
| UNE-EN 10025-3:2006 | Identical |
| ONORM EN 10025-3 : 2005 | Identical |
| DIN EN 10210-1:2016-01 (Draft) | Hot finished structural steel hollow sections - Part 1: General; German and English version prEN 10210-1:2016 |
| DIN 18800-7:2008-11 | STEEL STRUCTURES - PART 7: EXECUTION AND CONSTRUCTER'S QUALIFICATION |
| DIN 82016:2010-05 | Cargo lifting gear - Accessories and fittings for lifting and mooring - Cargo shackles |
| DIN HDBK 402 : 5ED 2009 | STAHL UND EISEN: GUETENORMEN 2 - BAUWESEN, METALLVERARBEITUNG - BETONSTAHL - STAEHLE FUER DEN STAHLBAU - FLACHERZEUGNISSE OHNE UEBERZUEGE - FLACHERZEUGNISSE MIT UEBERZUEGEN - SPUNDBOHLEN - VERPACKUNGSBLECH |
| DIN 743-3:2012-12 | Calculation of load capacity of shafts and axles - Part 3: Strength of materials |
| DIN 30690-1:2016-04 | CONSTRUCTION ELEMENTS IN THE GAS SUPPLY SYSTEM - PART 1: REQUIREMENTS FOR CONSTRUCTION ELEMENTS IN GAS SUPPLY SYSTEMS |
| DIN 1026-1:2009-09 | Hot rolled steel channels - Part 1: Taper flange steel channels - Dimensions, masses and sectional properties |
| DIN 1025-1:2009-04 | Hot rolled I-sections - Part 1: Narrow flange I-sections, I-series - Dimensions, masses, sectional properties |
| DIN EN ISO 16432:2007-09 | Resistance welding - Procedure for projection welding of uncoated and coated low carbon steels using embossed projection(s) (ISO 16432:2006) |
| DIN EN ISO 16433:2007-09 | Resistance welding - Procedure for seam welding of uncoated and coated low carbon steels (ISO 16433:2006) |
| DIN EN 10219-1:2016-01 (Draft) | Cold formed welded structural steel hollow sections - Part 1: General; German and English version prEN 10219-1:2016 |
| DIN 81249-2:2013-05 | CORROSION OF METALS IN SEA WATER AND SEA ATMOSPHERE - PART 2: FREE CORROSION IN SEA WATER |
| KTA 3205.2 : 2015 COR 2016 | COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS - PART 2: COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS FOR PRESSURE AND ACTIVITY-RETAINING COMPONENTS IN SYSTEMS OUTSIDE THE PRIMARY CIRCUIT |
| EN 10162:2003 | Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances |
| EN 10048:1996 | Hot rolled narrow steel strip - Tolerances on dimensions and shape |
| EN 10051:2010 | Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| EN 10221:1995 | Surface quality classes for hot-rolled bars and rods - Technical delivery conditions |
| EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| EN 10056-2:1993 | Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and dimensions |
| EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
| EN ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2009) |
| EN ISO 643:2012 | Steels - Micrographic determination of the apparent grain size (ISO 643:2012) |
| EN 10279:2000 | Hot rolled steel channels - Tolerances on shape, dimensions and mass |
| EN 10034:1993 | Structural steel I and H sections - Tolerances on shape and dimensions |
| ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| EN 10024:1995 | Hot rolled taper flange I sections - Tolerances on shape and dimensions |
| EN 10308:2001 | Non destructive testing - Ultrasonic testing of steel bars |
| EN 10306:2001 | Iron and steel - Ultrasonic testing of H beams with parallel flanges and IPE beams |
| EN 10163-2:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats |
| EN 10060:2003 | Hot rolled round steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| ISO 14713:1999 | Protection against corrosion of iron and steel in structures Zinc and aluminium coatings Guidelines |
| EN 10017:2004 | Steel rod for drawing and/or cold rolling - Dimensions and tolerances |
| EN 10163-3:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections |
| ISO 643:2012 | Steels Micrographic determination of the apparent grain size |
| EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
| EN 10020:2000 | Definition and classification of grades of steel |
| EN 10061:2003 | Hot rolled hexagon steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| EN 10059:2003 | Hot rolled square steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| EN 10055:1995 | Hot rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on shape and dimensions |
| EN 10160:1999 | Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) |
| EN 10067:1996 | Hot rolled bulb flats - Dimensions and tolerances on shape, dimensions and mass |
| EN ISO 14713 : 1999 | PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - ZINC AND ALUMINIUM COATINGS - GUIDELINES |
| CR 10260 : 1998 | DESIGNATION SYSTEMS FOR STEEL - ADDITIONAL SYMBOLS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.